519065
20
Zoom out
Zoom in
Vorherige Seite
1/44
Nächste Seite
Setting ALL Volume/Mute Control to any one Mode e.g. TV
This routine will set all Modes to punch-through to any one chosen Mode for Volume/Mute key
control without the needing to change to that Mode.
a.
Press and hold Setup key until “CODE SETUP” is displayed (takes approximately 2-3 seconds).
b. Release Setup key.
c. Navigate to “SYSTEM SETUP”. Press and release OK key. “VOL/MUTE SETUP” is displayed.
d. Press and release OK key. “VOL/MUTE. ALLE” is displayed.
e. Press and release the OK key. “WELCHER MOD.?” is displayed.
f. Press and release desired Mode key (TV, VCR, DVD, etc.) for Volume/Mute control.
g. “WARTEN…” will be displayed briefly followed by “FERTIG” and the remote will exit Setup and
return to normal operation.
h. All Modes will now punch-through to your chosen Mode for Volume/Mute control.
If the chosen Mode has no Volume/Mute commands of its own,
Fehler Set
“FEHLER” will be shown in the display and the remote will exit Setup
and return to normal operation.
Setting any Mode to use its own Volume/Mute Control
This routine will set any Mode to use only its own Volume/Mute control i.e. Volume/Mute punch-
through is disabled for this Mode. Note before using this routine to check the chosen Mode has
its own Volume/Mute functions, either in the code or by learning, otherwise the Volume/Mute
keys will do nothing.
a.
Press and hold Setup key until “CODE SETUP” is displayed (takes approximately 2-3 seconds).
b. Release Setup key.
c. Navigate to “SYSTEM SETUP”. Press and release OK key. “VOL/MUTE SETUP” is displayed.
d. Press and release OK key. “VOL/MUTE. ALLE” is displayed.
e. Navigate to “VOL/MUTE EINZ”. Press and release the OK key. “WELCHER MODE?” is
displayed.
f. Press and release desired Mode key (TV, VCR, DVD, etc.) to be disabled for Volume/Mute
punch-through control.
g. “ WARTEN…” will be displayed briefly followed by “FERTIG” and the remote will exit Setup and
return to normal operation.
h. The chosen Mode will now use its own Volume/Mute control.
Resetting Volume/Mute Control to Factory Defaults
This routine will reset Volume/Mute control back to its Factory default settings.
a.
Press and hold Setup key until “CODE SETUP” is displayed (takes approximately 2-3 seconds).
b. Release Setup key.
c. Navigate to “SYSTEM SETUP”. Press and release OK key. “VOL/MUTE SETUP” is displayed.
d. Press and release OK key. “VOL/MUTE. ALLE” is displayed.
e. Navigate to “VOL/MUTE RESET”. Press and release the OK key. “BESTAET. RESET” is
displayed.
f. Press and release the OK key.
g. “WARTEN…” will be displayed briefly followed by “FERTIG” and the remote will exit Setup and
return to normal operation.
h. Volume/Mute control is now rest to its Factory default settings.
20
55415 BedienAnltg TeFu_Zweite Version 08.12.09 16:33 Seite 20
20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Telefunken TRC 850 - 8in1 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Telefunken TRC 850 - 8in1

Telefunken TRC 850 - 8in1 Bedienungsanleitung - Englisch - 16 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info