649682
60
Zoom out
Zoom in
Vorherige Seite
1/164
Nächste Seite
- 60 -
c) CUSTOMISED PULSE-TRONIC
It is possible to select:
- the battery construction technology ( g. A.11)
choosing between:
“WET, GEL, AGM, PbCa”
- the charge current ( g.A.6) choosing between:
“AUTO” - automatic setting according to battery
conditions;
“BOOST” - rapid charge;
- the Ah - customised setting of the battery Ah ( g.
A.2) using 6 prede ned values selected using
the “MODE” button ( g. A.23), adjustable at 5 Ah
intervals using the “VOLT” button ( g. A.21), and
“FUNCTION” ( g. A.22).
Ah SETTING - EXAMPLE
15Ah 100Ah 300Ah
15Ah 100Ah 300Ah
DISPLAY
80Ah
75Ah
70Ah
. . . . .
. . . . .
100Ah
95Ah
90Ah
Note. The  nal charge voltage depends on the
technology of construction of the battery; to avoid
damaging the battery, pay special attention to the
technical speci cations given by the manufacturer.
Construction
Technology
Final charge voltage
6V 12V 24V
WET 7.7V 15.4V 30.8V
GEL 7.2V 14.4V 28.8V
AGM 7.35V 14.7V 29.4V
PbCa 8V 16V 32V
AUTO 7.2V 14.4V 28.8V
AUTO
7.7V 15.4V 30.8V
The PULSE TRONIC charge process ( g. A.17)
starts when the display stops ashing, each
individual phase is identi ed on the display ( g.
A.14) and terminates with the message ( g. A.2)
“OK”. The battery charge status is displayed
graphically in ( g. A.5). If the charge process is
not successful, an alarm message appears on
the display ( g. A.2) (see alarms list). When the
battery is charged, the battery charger switches
automatically to maintenance mode.
END OF CHARGE - EXAMPLE
CHARGE COMBINATION CHART
BATTERY TYPE
(T)
BATTERY CURRENT
(C)
AUTO
AUTO
AUTO BOOST
MANUAL “Ah”
AUTO
AUTO
AUTO BOOST
MANUAL “Ah”
WET
GEL
AGM
PbCa
AUTO
AUTO BOOST
MANUAL “Ah”
3.3.2 STORING OPERATION SETTINGS
It is possible to store the last function modes, so
they are immediately available after any switching
ON/OFF.
3.3.2.1 STORING PULSE-TRONIC CHARGE
Storage of voltage and type of battery, charge
mode.
Procedure:
- Check that the charge clamps are not connected
to a battery;
- Connect the power cable to the mains socket;
- Set the desired charge mode;
- Disconnect the power cable from the mains
socket.
3.3.2.2 STORING SUPPLY/DIAGNOSTIC
MODE
Storage of delivered voltage and current.
Procedure:
- Set the chosen mode and adjust the voltage/
current values as required;
- Turn on the lock settings by pressing, at the same
time, both keys “VOLT” ( g.A.21) and “MODE”
( g.A.23) for 3 seconds, on the display ( g.A.2)
( g.A. 4) will appear “LOK on.”
60

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln
1

Forum

telwin-doctor-charge-50

Suche zurücksetzen

  • Das Gerät ist am blinken und zeigt A.05 an was muß ich tun Eingereicht am 4-6-2024 21:03

    Antworten Frage melden
  • Ich habe Ladegerät angeschlossen zur Autobatterie und eingeschaltet,aber es blinkt LCC. Was bedeutet das? Eingereicht am 11-10-2021 14:27

    Antworten Frage melden
    • LCC steht für Limit Charge Current, also begrenzter Ladestrom. Es ist eine Schutzfunktion für tiefentladene Batterien. Sobald die Batteriespannung einen bestimmten Schwellenwert überschreitet, wird wieder mit eingestellter Stromstärke geladen. Beantwortet 23-7-2024 04:17

      Finden Sie diese Antwort hilfreich? Antwort melden

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Telwin DOCTOR CHARGE 50 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info