649682
62
Zoom out
Zoom in
Vorherige Seite
1/164
Nächste Seite
- 62 -
this function ( g. A.19);
- connect the battery terminal clamps, the message
“Go” appears on the display ( g. A.2);
- press the “VOLT” button ( g. A.21) to select the
battery voltage ( g. A.1);
- start the engine;
- check the display ( g. A.2) to read the battery
starting capacity and the following status:
- “OK” - STARTING CAPACITY OK;
- “SUF” - SUFFICIENT STARTING CAPACITY;
- “BAD” - INSUFFICIENT STARTING CAPACITY.
END OF TEST - EXAMPLE
DISPLAY LEGENDA
working
sufficient insufficient
3.5 BATTERY MAINTENANCE
The device has two advanced operating modes for
the maintenance of 6/12/24V batteries (ADVANCED
PROGRAMS), press and hold the “FUNCTION”
button for 3 seconds ( g. A.22) recommended for
AGM and WET type batteries:
- DESULFATION: recovery of sulphated batteries
( g. A.10);
- EQUALIZATION: reset of optimal battery
conditions ( g. A.9).
ADVANCED MENU SELECTION
3"
BEEEP
MENU
ADVANCED
PROGRAMS
On completing the selected process, disconnect the
power cable from the mains socket and disconnect
the clamps from the battery terminals.
BUTTON LOCK. It is possible to lock and unlock the
setting by simultaneously pressing and holding the
“VOLT” ( g. A.21) and “MODE” ( g. A.23) buttons
for 3 seconds, and ( g. A.2) ( g. A.4) “LOK on” and
“LOK off” will appear respectively on the display.
KEYBOARD LOCK
3"
DISPLAY
KEYBOARD UNLOCK
3"
DISPLAY
TO EXIT THE “ADVANCED PROGRAMS” MENU:
press and hold the “FUNCTION” button ( g. A.22)
for 3 seconds.
EXIT - ADVANCED MENU
3"
BEEEP
3.5.1 DESULFATION
Pulse system used to recover sulphated batteries
by applying enough voltage to neutralise the
surface layers of oxide and revitalize the underlying
plates. It is advisable to perform this operation with
the battery disconnected from the vehicle.
FUNCTION SELECTION
DISPLAY
ATTENTION! Pay particular attention to
the nominal voltage of the battery which must
correspond to the battery selected using the “VOLT”
buttonandindicatedonthedisplay(g.A.1).
Procedure
- press the “FUNCTION” button ( g. A.22) to select
62

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln
1

Forum

telwin-doctor-charge-50

Suche zurücksetzen

  • Das Gerät ist am blinken und zeigt A.05 an was muß ich tun Eingereicht am 4-6-2024 21:03

    Antworten Frage melden
  • Ich habe Ladegerät angeschlossen zur Autobatterie und eingeschaltet,aber es blinkt LCC. Was bedeutet das? Eingereicht am 11-10-2021 14:27

    Antworten Frage melden
    • LCC steht für Limit Charge Current, also begrenzter Ladestrom. Es ist eine Schutzfunktion für tiefentladene Batterien. Sobald die Batteriespannung einen bestimmten Schwellenwert überschreitet, wird wieder mit eingestellter Stromstärke geladen. Beantwortet 23-7-2024 04:17

      Finden Sie diese Antwort hilfreich? Antwort melden

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Telwin DOCTOR CHARGE 50 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info