Bedienungsanleitung Teufel DecoderStation 7 (Seite 15 von 20) (Englisch)

562467

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

• DecoderStation 7 15

Crossover frequency

With the crossover frequency, you deﬁne the frequency,

up to which the subwoofer should be active. Possible

values: 80 to 250 Hz in eight steps.

You can also set the edge steepness: This is the level,

which is still present at the subwoofer above the crossover

frequency. Possible values: –24 dB and –36 dB.

Enter –24 dB for normal speakers. For satellite speakers

with bassreﬂex openings, the acoustic efﬁciency declines

more sharply — so select -36 dB for optimal actuation of

the subwoofer.

You can ﬁnd information on the recommended crossover

frequency in the technical data of the satellite speakers in

our webshop.

Distance

The surround sound effect may be corrupted if the speak-

ers are positioned at different distances to the listening

position. To compensate for these differences in run time,

you can set slight signal delays for all channels. Measure

the difference from the listening position to the speakers

and enter these values in the menu. The system calculates

the required delays on this basis.

“System Setup” menu

HDMI

CEC (Consumer Electronics Control)

If this function has been activated (ON), CEC-compatible

devices are controlled with a control command issued via

the HDMI connection. For example, the DecoderStation 7

and the connected devices are automatically activated

and deactivated via the remote control of the TV set.

ARC (Audio Return Channel)

This option offers receiving audio from the TV via the

HDMI cable (for TV sets that support this function).

Audio from television sets runs to the DecoderStation 7

through the HDMI cable without having to connect

another cable. If the ARC function is activated, the

“COAXIAL 1” input (9) is no longer available.

Possible settings: OFF, ON.

Important!

Please note that many television sets only have

one HDMI input that supports the ARC function.

To use ARC you must also activate CEC.

Note: If the CEC function is activated, standby power

consumption increases.

Automatic deactivation

After a certain time of inactivity, the device automatically

switches to standby after a preset time. Possible values:

60 min. (default), 30 min., never.

Power On Level

Here you can set the volume of your device when it is

activated:

• last: The volume that was set at deactivating.

• ﬁxed: Fixed volume from -40 dB (low) to +10 dB (very

loud).

5.1/7.1

With this, you can switch between 5.1 and 7.1 operation

and also set the function of the analogue output 14 “RC/

PRE OUT” (see page 10), which you can connect a stereo

ampliﬁer, active speaker or radio transmission system.

This makes it possible to project sound into another room

or connect to the rear center speakers in 7.1 opera-

tion using RF audio transmission system (such as Teufel

Rear Station 4).

5.1 Converts (via downmix) the 5.1 audio

signal to a stereo channel (2.0) to project

sound into a second room.

7.1 7.1 Operation with output of the additional

rear channels.

D/E

You can set the OSD menu language this way. Possible

values: German, English

The menu in the unit display panel 2 is always in English.

System Reset

This resets the device to the factory default.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Teufel DecoderStation 7 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info