Bedienungsanleitung Thermocet Beverly S (Seite 6 von 26) (Englisch)

607254

Zoom out

Zoom in

Vorherige Seite

1/26

Nächste Seite

Page 6

Setting first period of heating.

Press the button B4 (3x) until P 1 and

) appears on the display.

Press button B4 for slightly longer until the start time begins to flicker and appears and set the time for the start of the first period of

heating by means of the buttons B1and B2 ; hours/minutes.

Press button B4 again so that P 1 and ) appears after which the time can be set to the end of the first period of heating by means of the

buttons B1and B2 ; hours/minutes.

Press button B4 for slightly longer until the display P 2 and

* appears and set the time for the start of the second period of heating by

means of the buttons B1and B2 ; hours/minutes.

Press button B4 again so that P 2 and ) appears after which the time can be set to the end of the second period of heating by means of

the buttons B1and B2 ; hours/minutes.

Wait or press button timer again and the display will return to the start.

2.2 Igniting the apparatus

* Press buttons B1and B3 at the same time until an acoustic signal indicates that the start procedure has

begun for igniting the apparatus. Once the ignition of the pilot burner has been achieved the gas block will

set the flame height automatically to maximum.

* You can regulate the flame height by pressing on button B1 or B2 for higher or lower flame height

respectively. In order to set the apparatus on “Standby” you press on button B2 until just the pilot burner is

burning.

Warning

Wait at least 5 minutes before attempting to re-ignite the unit after turning off the pilot. Gas fires become hot

when in use. Therefore care should be taken, for instance children and those requiring help should be kept away

from the immediate area where the fire is burning. Gas fires must not be placed on or against flammable materi-

als (curtains, etc.).

2.3 Technical data:

Radio controlled Transfer Frequency:

ON 40.5 kHz, OFF 40 kHz

Range: 0.5…10m

Ambient temperature:

Transmitter and receiver: max. 60ºC

Connection cables: max. 180ºC

Maintenance

The painted parts can be wiped with a soft, moist cloth. The unit must be switched off immediately if something

has been spilled on the fire. Once the fire has cooled down the spillage can be removed with water and soft soap.

Never use an abrasive cleaning agent!

Any deposits on the glass can be removed by using a glass cleaner. We recommend having the fire and the chim-

ney checked by a fitter and having them cleaned before each heating season. If the special heat-resistant glass is

broken or cracked it should be replaced immediately before the unit is switched on again.

It is better to leave the pilot burning during the heating season (due to possible condensation formation in the

unit).

Please note: As the manufacturer we are aware that faults may occur in the electronic control of gas fires and the

great inconvenience this may cause you. Therefore we have drawn-up additional installation instructions. (See

pages 18 and 19.)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Thermocet Beverly S Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info