Bedienungsanleitung Thermocet Flat Fire M (Seite 6 von 30) (Englisch)

607255

Zoom out

Zoom in

Vorherige Seite

1/30

Nächste Seite

Page.6

Preparations for installing the Flat Fire

Always check all parts for possible damage or breakage. The Decorative Glass or Decorative Steel Front( de-

pending on whichever you have chosen) should be carefully taken out of the box. Put the Decorative window in a

place where it will not become damaged or broken. This also applies to the Decorative Steel Front. The box for

the Decorative Window or the Decorative Steel Front also contains a template which you can use in positioning

the fire ( See Page 15 ). First take the glass window off the fire to prevent any damage to the window during in-

stallation of the fire. See point 3 on page 5 “Installation instructions Flat Fire with concentric duct connection”.

Now take the accessories out the box with care, so that the fire can be removed and fixed to the wall. The fire is

now ready to be installed

3. Installation instructions for the Flat Fire with concentric duct connection

General instructions

• The fire should only be installed and connected by a registered installer, in accordance with the local Gas

Appliance Instructions. Also see Page 3 “Important information”.

• Never place the fire against or in a flammable wall.

• The gas connection must be stress- free, to ensure no damage occurs to the gas regulating equipment.

• Check the gas connections for leaks, using soapy water or leak detection spray. Light the fire in accordance

with the operating instructions and check that the shape of the flame is even.

• After the first firing, you will need to remove any deposit left on the glass window.

Distances to non- combustible materials.

Non- combustible surfaces are defined as brick, marble, concrete etc. and also a number of man-made materials

impervious to flame. If in doubt, refer to the material manufacturer for further information before proceeding

with installation. It is recommended that there is at least 300mm clearance above the outlet grille. Minimum

clearance from the bottom of the outer frame to the floor must be 200mm, however, clear and easy access to the

controls located on the bottom side must be allowed for. Clearance to the sides of the heater is 100mm. Clearance

to the front of the heater is 1000mm. Care must be taken that no brickwork or other incombustible material pro-

trudes into the area immediately around the base of the heater or area underneath the heater in a way that is likely

to affect natural airflow into or around the heater.

Components of the fire ( See Page 13 fig. 1 )

1 Combustion unit 12 Flue connection 100mm

2 Burner 13 Air chamber

3 Recirculation plate 14 Wall brackets bottom

4 Injector bracket 15 Wall brackets top

5 Burner support 16 Flue connector 150mm

6 Pilot burner 17 Casing

7 Glass holder top 18 Bottom panel casing

8 Glass holder bottom 19 Glass window combustion chamber

9 Glass holder left 20 Decorative panel

10 Glass holder rigth 21 Decorative Steel front

11 Bold for front

Installing the fire

Caution: Before you install the fire, it is advisable first to read Section 4 “Concentric duct system” on Page 7,

regarding installation of the restriction sheet iron, if required

• The box for the Decorative Glass ( 20 ) or the Decorative Steel Front ( 21 ) contains a template for use in

determining the position where the fire will be hung. Drill the holes for suspending the fire and the hole for

the concentric duct. Insert the cotter bolts provided into the four drilled holes and then remove the nuts

from the cotter bolts.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Thermocet Flat Fire M Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info