Bedienungsanleitung Thermocet Trimline Quadro 46 (Seite 8 von 85) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Spanisch)

532670

Zoom out

Zoom in

Vorherige Seite

1/85

Nächste Seite

Page.7

Ensure that the fuel supplied to the unit is clean and free from particles and moisture.

Before a gas supply pipe (new or existing) is connected to the main gas pipe at the gas meter and to

the gas control block of the unit, clean and dry compressed air should been blown through it.

Cut copper pipes as well as aluminium pilot pipes must be deburred and blown clean before they

are connected. The dust filter at the connection to the gas control block will only filter out the

coarsest dirt from the system. Fine particles are still able to reach the inside and may damage and/or

adversely affect regulation in the gas control block .

Heat, moisture and dust are a threat to all electronic components

Protect the electronic gas control

until

all construction, plastering and paintwork has been completed.

If such work cannot be avoided, then protect the control against dirt and moisture penetration by using,

for example, plastic film .

Only place the batteries

after

wiring to the receiver, gas control block and pilot set is connected.

Premature connection to the energy source may damage the control’s CPU (central processor).

Ensure that the ignition cable is not near the antenna wire and that they do not cross each other.

The high voltage released at ignition may damage the sensitive receiver circuit.

This may mean that the unit becomes less responsive or not responsive at all to handset commands.

Extend the supplied thermocouple with just the original extension. (available from your supplier)

Unauthorized extension of the thermocouple has the effect of stress reduction, thereby

the magnetic coil can not be activated.

Prevent leakage of the ignition spark to other parts of the installation than the Ignition by the pilot

Keep the ignition free of hull or other metal parts. If cable extension is used, see to it that connections are

additionally insulated with silicone grommet.

For automatic start via the transmitter, the receiver and the control the gas control valve to

be switched

The oval disk on the gas control block should be turned to the ON position. The I/0 switch should

to be set to "I". The ignition must be connected to the receiver box at the terminal SPARK.

The transmitter's contains the thermostat sensor system

The transmitter operates best at 2 to 3 m from the unit. Although the communication via short wave radio

signals takes place, it is recommended that the transmitter in the 'visibility' of to lay the gas apparatus in

a place where the user wants to experience a pleasant temperature. Place the hand transmitter in direct

sunlight or other hot places. The thermostat measures the temperature and regulates the flame size of the

gas in accordance.

Remove batteries only with the red ribbon which is under the battery, not with metal tool

Removing batteries with a metal object, the electronic control can permanently damage.

5. INSTRUCTIONS FOR MERTIK MAXITROL GV60 GASCONTROL

Electronic components will become permanently faulty when exposed to temperatures higher than 60°C.

Standard AA batteries will crack open at temperatures >54°C and the battery contents will damage the

electronic switches located underneath. Batteries last longest at <25°C. At >50°C the life span is around

23 weeks, this makes the use of the gas fire unnecessarily expensive.

Only install the gas control block and receiver as pre-installed at the factory

Remember that components may have to be replaced or that repairs may have to be performed at a later date.

This may be more difficult if the control is installed using a method that is different from the instructions

provided here.

WARNING

Do not tighten the contact breaker and the thermocouple connection too tightly on the gas control

block or to each other. It is sufficient to tighten by hand and add a half a turn with an open-end spanner.

Tightening too much will break the connection to the magnetic coil below and/or the insulation around

the aluminium contact pin in the contact breaker. This may lead to the magnetic coil not opening the gas

supply to the pilot and the unit not working.

NOTICE

WARNING

It is forbidden to start up the unit if window (s) is not present or broken!

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Thermocet Trimline Quadro 46 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Thermocet Trimline Quadro 46

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info