Bedienungsanleitung Thermocet Trimline Quadro 46 (Seite 10 von 85) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Spanisch)

532670

Zoom out

Zoom in

Vorherige Seite

1/85

Nächste Seite

Page.9

Exterior wall duct without bends (See illustration A)

Always place a length of X=1 metre vertically on the appliance, directly followed by a 90-degree

bend and the standard length exterior wall duct set, Y=0.6 metres.

Exterior wall duct with horizontal bend and deviation of Y=4. (See illustration B)

Always place a length of X=1 metre vertically on the appliance and the course can be continued with

one 90-degree bend (nominal length per bend is 2 metres). A maximum horizontal deviation of

Y=4 metres can then be made. Ensure there is adequate slope and take the horizontal length of the

bend itself into account. Note: In some situations the flue pipe should possible be placed close to the wall.

Thus the 90° bend can not make the shortest radius; to overcome this the hole in the wall for the 90° bend

can be made lightly oval shaped.

Roof duct without bends (See illustration C).

A direct course without bends is possible to a maximum length of X=12 metres, measured from the

connection to the appliance. The minimum length is 3 metres. The outlet can be positioned anywhere in

the roof surface, whether flat or sloping; flue gas outlet and combustion air inlet are in the same pressure area.

Until 6 metres restrictor - A- should be used. From 6 metres till 12 metres restrictor - A - and - B - should be used.

Roof duct with 45-degree bends (See illustration D).

Always place a length of X=1 metre vertically on the appliance. The route can then be continued with two

45-degree bends until the maximum length of 12 metres is reached (Y+Z= 8 metres maximum). The nominal

length of the 45-degree bend is 1 meter. Until 6 metres restrictor - A - should be used. From 6 metres till

12 metres restrictor - A - and - B -.should be used.

Roof duct with 90-degree bends til Y=8meter. (See illustration E).

Always place a length of X=1 metre vertically on the appliance. The route can then be continued with one

90-degree bend (nominal length per bend is 2 metres) until the maximum length of 12 metres is reached.

Take a maximum horizontal path of Y= 4 metres into account (measured between bends) and ensure the

slope is adequate. Until 6 metres restrictor - A - should be used. From 6 metres till 12 metres restrictor - A—and - B -

should be used.

Direct external wall duct plus use 90° bend (See illustration F).

Decide on the position of the appliance and connect up the wall duct set. The

wall duct set will have to be shortened if the appliance is being installed di-

rectly against the wall (cavity wall for example). (Y=0.725 metres max.)

Connection to conventional chimney (using the renovation kit)

The concentric connecting pieces for existing flues should be used for this pur-

pose and the installation instructions (apply for these separately) must be fol-

lowed strictly. Until 6 metres restrictor - A - should be used. From 6 metres till

12 metres restrictor - A - and - B should be used.

7. CONCENTRIC CHIMNEY LAY OUT

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Thermocet Trimline Quadro 46 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Thermocet Trimline Quadro 46

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info