Bedienungsanleitung Thermocet Trimline Quadro 46 (Seite 12 von 85) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Spanisch)

532670

Zoom out

Zoom in

Vorherige Seite

1/85

Nächste Seite

Page.11

8.3 Installation instructions regarding existing flues. (see APPENDIX 3)

Instructions

The flue gas exhaust system falls within category C91 and must be built in accordance with national

rules and regulations and the instructions of the manufacturer, as specified in the documentation and

installation instructions.

This means, among other things, that the existing chimney must not be smaller than 150 mm

round / square, but no larger than 200 mm, and not ventilated by grilles etc. In the case of larger chimney

size, a flexible hose of around 150 mm may possibly be used in combination with a flexible hose of around

100 mm, as described below. For other situations, you should consult your supplier / manufacturer.

8.4 Components

Check all parts for damage before commencing the installation. You will require the following parts for

converting a brickwork duct to a balanced flue concentric duct :

Note: The renovation kit consists of parts 4, 5 and 7.

8.5 Installation

* Guide the flexible hose (6) through the existing duct.

* Attach the adjustable pipe (5) to the bottom of the flexible hose and secure this in place using 2 parkers.

* Level the bottom side of the adjustable pipe (5) with the ceiling of existing chimney.

* Shorten the flexible hose to approximately 100 mm above the existing chimney top.

* Attach the mounting plate / connecting piece (7) to the flexible hose on the roof. Clamp it with a hose

band and secure it in place using a parker.

* Attach the mounting plate / connecting piece (7) to the chimney top, using silicone sealant to make it

watertight secure with stainless steel screws.

* Install the roof terminal (9) and secure it in place using the supplied locking band (8).

* The adjustable pipe (5) will stick about 100mm below ceiling/existing chimney. Mount the inner ceiling

plate (4) gastight to the ceiling/existing chimney with silicone kit and fixing screws.

* Position the unit in accordance with the instructions of the unit manufacturer.

* Always install a minimum of 1 metre of concentric duct type THC CC100-150 (2), or 130-200 mm with

reduction to 100-150 mm.

8.6. Cleaning and maintenance.

This appliance should be inspected and serviced once a year by a qualified, competent and registered person.

The inspection and maintenance must at least ensure that the appliance is working correctly and safely.

It is advisable to clean the appliance of any dust and debris before regularly during the heating season and

especially if the appliance has not been used for some time. This can be done with a soft brush and a vacuum

cleaner or a damp cloth and if required a non-abrasive cleaning agent. Do not use corrosive or abrasive

substances to clean the appliance.

The Concentric flue system must be inspected and cleaned every 2 years.

Also control of:

1 Gas tightness of gas fire and concentric flue system.

2 The correct operation of the gas control and the ignition of the burner.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Thermocet Trimline Quadro 46 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Thermocet Trimline Quadro 46

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info