Bedienungsanleitung Thermocet VERSA LV-HV (Seite 3 von 14) (Englisch)

607247

Zoom out

Zoom in

Vorherige Seite

1/14

Nächste Seite

Page.3

We wish you happy heating with the purchase of this ThermoCet recessed gas fireplace. Please read

these instructions thoroughly before installing and using the fireplace. Keep these instructions care-

fully. Always state model and serial number in the event of a breakdown.

1. GENERAL

1.1 Delivery

You should inspect the appliance for damage in transit, immediately it has been delivered. If it is damaged,

you should report this without delay and as precisely as possible to your supplier. Please refer to the delivery

document.

1.2 Contents of packaging

1 x Completely assembled appliance

1 x Operation and installation manual

1 x Warranty card

1 x Pipe mouth with 4 self-tapping screws for connection of outlet

1.3 First firing

Your fireplace is coated with heat-resistant enamel that can withstand extremely high temperatures. Burn the

fire at high during the first hours of use and ventilate the room well. The curing of the enamel may produce a

smell/smoke, but this is harmless, however. Any marks on the glass can be removed immediately with glass

cleaner.

1.4 Guarantee ( see page 13 and 14)

Always complete your guarantee card in full and return it to your supplier immediately after purchase. Type

and serial number are shown on the plate that you will find on the bottom of the burner unit.

2. OPERATING INSTRUCTIONS VERSA

The Versa has a combined glow-effect and main burner (see page 10 figure 4). This burner can be operated

with either the thermostat knob (A) or the manual slide (B). You select the required setting with the thermo-

stat knob (A) and the modulating thermostat provides the right temperature. The hand-operated slide (B) al-

lows you to select the flame height you wish and the burner will continue to burn at that setting until you

change the selected setting.

2.1 Igniting.

* Open the gas stopcock fitted in the gas pipe to the appliance.

* Ensure that the thermostat knob (A) is at position n in the initial setting.

* Turn the thermostat knob (A) to the ignition position.ô

* Push the thermostat knob (A) and keep it pushed in.

* Push the ignition knob (C) all the way in until you hear a “click”; this is the spark ignition.

* You can see through the glass window whether the pilot light is burning. “Click” a few more

times if necessary, until the pilot light ignites.

* Keep the thermostat knob (A) pushed in for about another 30 seconds when the pilot light starts

burning and then release the knob.

* If the pilot light does not continue to burn, wait 5 minutes and then repeat the procedure.

* The burner is ignited by turning the thermostat knob (A) to the required setting (between set

tings 1 and 7, depending on the required temperature).

* To ignite the appliance with the glow-effect burner, move the slide (B) from position n depend-

ing on the required flame height (see figure). The glow-effect burner only functions when the

thermostat knob is between positions 1 and 7 (position 1 = low, position 7 = high).

Remark

Position (1) on the thermostat knob (A) is the pilot light setting if the room temperature is 10°C or more. If

the room temperature is below 10°C, the burner will also start to burn in position (1) until the temperature

has risen to 10°C.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Thermocet VERSA LV-HV Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info