771207

Thermor VM 080 D400S Seite 10

10
Zoom out
Zoom in
Vorherige Seite
1/141
Nächste Seite
9
Indicators
Indicator status
Meaning
On
Absence mode activated: The water heater is frost-protected (7°C). The
BOOST function is deactivated.
On
Manual mode selected:
To set the temperature of hot water, touch the buttons until the desired
level is selected on the Water Drop LEDs (5 levels available).
On
ECO+ mode activated; the water heater starts reading consumption to
adapt to the needs of the user and ensure energy savings, whilst
guaranteeing comfort levels.
Segments of the
water drop
lightening one
after another
The BOOST function is activated by a quick press. Activating the BOOST
mode sets the heating temperature to the Max level for 1 hour. After the
heating is done, the appliance will return to the mode that was selected
before activation of the BOOST mode.
Blinking
Water heater pairing in progress.
On
Paired water heater connected.
On
The appliance is not heating water. The lit segments show the quantity of
available hot water.
Blinking
The appliance is heating water to reach the required level. The fixed lit
segments show the quantity of available hot water.
Top segment is
lit in orange
The appliance is malfunctioning. Check the list of error codes below or
contact the after-sales services
Connectivity
- If your appliance as the Wifi picto , it can be operated via your smartphone or tablet.
- To enable this, the following accessories are required:
- An Internet router or hub
- The Cozytouch application, compatible with IOS and Android.
- After the application is installed, ensure you have the ID and password for your Internet router or hub and open the
Cozytouch application. Follow the step-by-step instructions to create your account and then pair your appliance.
- Once the procedure is complete (as stated in the application installation procedure), check the inbox for the email
account used for registration to activate your user account. You can then log in and access all of our services.
IMPORTANT: during the pairing process:
- Please ensure your smartphone (or tablet) is left near your water heater
- Your product will beep several times (this is completely normal)
NOTE: The Wi-Fi signal in the area where your product is installed must be sufficient
DECLARATION OF CONFORMITY - RED DIRECTIVE 2014/53/EU (Radio Equipment Directive)
ECET hereby declares that the equipment specified below meets the requirements stipulated by the RED Directive
2014/53/EU.
The full EU declaration of conformity for this equipment is also available on request, from our after-salesservice (see
the back of this manual for details and address).
Designation: D400 Successor wall-mounted electric water heater
Models: 50,75,95 L
Specific cautions:
Radio frequency bands used by the Transmitter-Receiver: Wi-Fi 2.4G: 2400 MHz to 2483.5 MHz
Maximum radio frequency output: <20 dBm
Class 2 equipment: can be marketed and commissioned without restriction
Radio range: from 100 to 300 metres in a free field, variable according to the associated equipment
(the range may be affected by the installation conditions and the electromagnetic environment).
Compliance with the Radio and Electromagnetic Compatibility standards has been checked by the following
notified body: SGS Fimko Ltd Helsinki,Finland
7. MAINTENANCE
- Before removing the plastic cover, make sure the power is turned off to avoid any risk of injury or electric shock.
The domestic maintenance must be done by the user. Operate the safety device every month to prevent scaling and
check that it’s not blocked. Not executing this maintenance may cause damage and the loss of the warranty. Maintenance
by qualified personnel A: Scaling: Remove the scale deposited as mud. Do not scratch or hit the scale sticking to the
walls to avoid damage to the coating. Do not forget to change the seal and reassemble the appliance, check that there is
no leakage of water after the first heating. B: For devices with magnesium anode, change the magnesium anode every
two years or as soon as its diameter is less than 10mm. C: The change of a sheathed heating element involves draining
of the water heater and the change of the seal. Reassemble the heating element, reasonably tight nuts (cross tightening),
check that there is no leakage after the first heating-up, and tighten again if necessary. D: Drain: Turn off power and cold
WIFI models only
WIFI models only
WIFI models only
… 10 …

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Thermor VM 080 D400S wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info