Bedienungsanleitung Thomson ROC Z907 (Seite 6 von 50) (Deutsch, Englisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch)

699754

Zoom out

Zoom in

Vorherige Seite

1/50

Nächste Seite

7.2.1 Fixed code/ Rolling code procedure(with

manual registration for synchronisation with the

door system)

Forsome door operator manufacturers, it is additionally

necessary to register/synchronise the handheld transmit-

ter with the receiver of the door operator system.

•Please consult the operating instructions for the door

operator (thereisgenerally asection on registering a

new handheld transmitter).

•Make surethat you areclose to the door operator

receiver (about 50 cm).

•Usually aset button is activated on the door operator

system to register handheld transmitters, and aLED

lights up (can vary according to manufacturer).

•Normally,you now have about 20–30 seconds to

•Synchronisation generally takes place when you press

the programmed/copied button of the ROCZ907 three

times in succession.

7.2.2 Rolling code procedure(with automatic reg-

istration for synchronisation with the door system)

Due to the rolling code principle, it is often necessary to

receiver of the door operator system.

•Please consult the operating instructions for the door

operator (thereisgenerally asection on registering a

new handheld transmitter).

•Make surethat you areclose to the door operator

receiver (about 50 cm).

•Usually it is sucient to press and hold the pro-

grammed button of the ROCZ907 until the redfunction

LED (1) ashes quickly (about 10 seconds).

•Now release the button. The remote control goes into

synchronisation mode with the door operator system. The

latter conrms the synchronisation after about 5–10 sec-

onds by means of an illuminated or ashing LED. Once

synchronisation has ended, the fast ashing redLED on

the ROCZ907 goes out; registration was successful.

7.3 Copy function –complex rolling code

Some door operator manufacturers requiretransmission

of the source code (often also called SEED code) to be

able to teach in the ROCZ907 onto the door operator.

Here, it is essential to have the original functioning hand-

held transmitter (master function)with the source code!

Depending on manufacturer,the procedureofthe

original remote control for transmitting the source code

(master remote control) is now implemented.

Details of the procedurecan be found in the original operat-

ing instructions for the handheld transmitter or door operator.

7.3.1 Example for BFT (manufacturer):

•Beforeperforming the copy function, make surethat

the original handheld transmitter and the ROCZ907

arefacing each other and not morethan 3cmapart.

•Make surethat you areclose to the door operator

receiver (about 50 cm).

•Press and hold the ‘1’ button on the ROCZ907 and

keep it held while pressing the ‘2’ button four times.

Release both buttons. The redfunction LED (1) now

ashes about every 2seconds.

•Onthe original handheld transmitter,press and hold

the button you arecopying until the redfunction LED

of the ROCZ907 lights up and successively ashes

twice about every 2seconds.

•Now press the button concealed on the back (battery

compartment) (old BFT models) or buttons 1and 2

(newer models) on the original handheld transmitter

(master). The redLED on the ROCZ907 ashes quickly

in succession. Now press and hold the button you

wish to program (for example, ‘1’) until the redLED of

the ROCZ907 goes out.

•Press and hold the programmed button of the ROCZ907

until the redLED ashes quickly (about 10 seconds).

Release the button. Programming has been completed

when the redLED on the ROCZ907 goes out.

•Then check whether the door can be controlled using

the button that has been taught to; if not, repeat the

procedure.

7.3.2 Example for FAAC,Genius, Amigo, Kilo

(manufacturers):

•Beforeperforming the copy function, make surethat

the original handheld transmitter and the ROCZ907

arefacing each other and not morethan 3cmapart.

•Make surethat you areclose to the door operator

receiver (about 50 cm).

•Press and hold the ‘1’ button on the ROCZ907 and

keep it held while pressing the ‘2’ button four times.

Release both buttons. The redfunction LED (1) now

ashes about every 2seconds.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Thomson ROC Z907 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info