Bedienungsanleitung Thomson ROC4218 4in1 (Seite 7 von 54) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

607846

Zoom out

Zoom in

Vorherige Seite

1/54

Nächste Seite

3. Press the key that corresponds to the type of

equipment you want to control:

TV: television set, DVD: DVD player, SAT: satellite

receiver, cable, DVBT, ADSL, AUX: any other

appliance.

4. While the indicator is lit, enter the ﬁ rst digit of the

4-digit code proposed for the set to be controlled

(example: 0166 for a Thomson TV).

5. Direct the remote control towards the set and try to

switch it off by pressing the key G.

6. Should the set not switch off, repeat step 2. Then

type in the next 4-digit code. Try to switch off the

set by pressing key G once. Repeat this procedure

by trying out each of the 4-digit codes.

Check of the programming:

In principle, your set is ready for receiving the remote

control commands.

Check your remote control for proper functioning by

performing the test described on page 2.

Method C – Programming by means

of code retrieval

Should none of the codes work, you still have the

possibility of retrieving the appropriate code without

having to perform any input.

1. Switch on the set you want to control.

2. Hold down the SETUP key until the key that

corresponds to the last mode you selected blinks

and then remains lit.

3. Press the key that corresponds to the type of

equipment you want to control:

TV: television set, DVD: DVD player, SAT: satellite

receiver, cable, DVBT, ADSL, AUX: any other

appliance.

4. Direct the remote control towards the set and try to

switch it off by pressing the key G.

5. If the set you want to control switches off, press

OK to memorise the code.

6. Should the set not switch off, press key G as many

times as required (up to 200 times), until the

set switches off. Between two key presses, leave

enough time for the key corresponding to the

selected mode to light up again (about 1 second).

Proceeding this way will enable you to see whether

the set responds or not.

7. Immediately upon the switching-off of the set to be

controlled, press OK to store the code.

Check of the programming:

In principle, your set is ready for receiving the remote

control commands.

Check your remote control for proper functioning by

performing the test described on page 2.

Try out other remote control keys to ﬁ nd out the range

of functions you can control. If you think that not all of

the keys are active, repeat the procedure of this

programming method to ﬁ nd out the code supporting a

wider range of features.

Method D – Automatic

code search

With this method, the remote control scrolls through

the full code list by sending an IR signal to the set to be

controlled remotely. Proceed as follows:

1. Check that your equipment is on. If not, switch it on

manually.

2. Hold down the SETUP key until the key that

corresponds to the last mode you selected blinks

and then remains lit (the indicator light remains on

for a few seconds to give you the time to proceed

with the following steps. The indicator lamp ﬂ ashes

to signal that this time is almost up, and then goes

off).

3. Release the SETUP key.

4. Press the key corresponding to the type of

equipment (for example TV).

5. Press the P+ or standby G or B (DVD only) key.

After a few seconds, the remote control begins to

scroll through the whole code list included in the

library (at a rate of roughly 1 code per second).

Press the P+ key once again to slow down the test

speed (1 code every 3 seconds). As soon as the set

changes channels, you must press OK to save the

code and stop the remote control scrolling through

the list. If you do not react quickly enough, you can

go back to the previous code by pressing P- or E

( DVD only) as many times as necessary (you can

go forward by pressing G, P+ or B (DVD only)

if you have gone back too far). As soon as the set

responds again, press OK to save the code.

Method E – Programming for control of

a COMBO (combined TV-VCR, TV/DVD,

VCR/DVD, … set)

Depending on the COMBO group (TV/VCR, VCR/

DVD, etc.) and the make, you will be required to

enter a single code for both devices in the COMBO, or

to enter two codes, one code per device. Consult the

separate list to discover this.

Before you start programming, you must ﬁ nd the

subcode or code of the subset to be controlled

(television or video recorder, ...). Refer to the list

supplied with this user manual (see page subcodes

or codes).

1. Switch on the COMBO you want to control.

2. Hold the SETUP key down until the key

corresponding to the last selected mode blinks and

then remains lit.

3. Press the key of the ﬁ rst device to control, and then

follow one of the programming methods A, B, C or

D previously described.

4. If a second code programming is required, then

repeat steps 2 and 3 above.

How to retrieve

a programmed code

It may be useful to retrieve the code programmed in

the remote control.

1. Hold down the SETUP key until the key that

corresponds to the last mode you selected blinks

and then remains lit.

2. Press the key that corresponds to the type of

equipment you want to control:

TV: television set, DVD: DVD player, SAT: satellite

receiver, cable, DVBT, ADSL, AUX: any appliance.

3. Press the SETUP key brieﬂ y, so that the last mode

selected blinks once.

4. Press the numbered keys in ascending order (0 to

9) until the selected mode blinks once.

5. The number that caused the selected mode to blink

is the ﬁ rst of the four numbers that make up your

code. Make a note of it below.

6. Repeat step 4 to ﬁ nd out the other numbers of the

code.

7. When the fourth number has been found, the

indicator light for the selected mode goes out.

Check of

the programming

- For a television or a satellite receiver: switch on

and, for example, press 2 to change channels.

- Video recorder: load a tape and then press B.

- DVD player: load a DVD and then press B.

Try other remote control keys to ﬁ nd out the range of

functions you can control. If you think that not all of the

keys are active, try the programming Method B or C.

When you have retrieved the code of

your set, jot it down so that you can use it

whenever needed.

After battery replacement, you may have to

programme the remote control again.

DVD CODE

TV CODE

STB CODE

AUX CODE

00131793bda.indd Abs1:2

131793bda.indd Abs1:2

19.08.2008 16:01:26 Uhr

19.08.2008 16:01:26 Uh

Thomson ROC4218 4in1 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info