Bedienungsanleitung Thomson THS813 (Seite 11 von 30) (Englisch)

658794

Zoom out

Zoom in

Vorherige Seite

1/30

Nächste Seite

QUICK GUIDE TO USING YOUR RECEIVER

P11

Please read the displayed instructions for each screen carefully. They will help you adjusting the settings fast and

easy.During the First Time Installation, you can press BLUE Next to go to the next step or YELLOW Previous to get

back to the previous step.

4.2 Audio and Subtitle Setup

Here you can set the Audio Language, Audio output, Subtitle Display and Subtitle Language. Use pq for selection

and tu to change settings. To see a list of all possible settings for the highlighted option, press OK. Once all

settings have been made, press BLUE Next to continue or YELLOW Previous to get back to the previous setup

screen.

Please read the displayed instructions for each screen carefully. They will help you adjusting the settings fast and

easy.

4.3 Auto DiSEqC Scan

In this menu the receiver will do an automatic scan for connected LNBs and suitable satellites. The most

common satellites as Astra 23.5E, Astra 19.2E, Astra 28.2E, HotBird 13.0E and Eutelsat 9.0E will be scanned for

availability. Please wait for a short time to let the receiver complete the scan and then apply the settings to

the next step by pressing OK at Next. Press OK at Previous if you have forgotten to connect a satellite cable or

need to correct anything else that was adjusted before. Once the Auto DiSEqC scan is finished and you have

confirmed with OK you will automatically receive at the next step of FTI.

To ensure reception and to scan the channels from your operator follow the Fast Scan method in the next steps.

For this the reception of Astra 23.5E is essential.

4.4 Satellite Selection

Depending on the results of the found satellites in the previous installation step it is possible to setup other

or additional satellites connected to your installation system. This might be useful if you have other satellites

installed on the LNB which are not commonly used ones or if the found satellites need rework.

To check or change your settings for the satellite(s) connected to the ports, use pq and press OK to enter the

submenu of your choice (LNB and the configured satellite will be according to Auto DiSEqC Scan result). This you

can do for up to 4 satellite positions. For a detailed description of this setup, please see chapter below. Once all

settings have been made, press BLUE Next to continue.

4.5 Channel List Selection

Here you can decide which of the Fast Scan channel lists you want to install. Use pq to highlight your

selection in orange coloured letters. Press OK to choose a list and the receiver will start the scan for the list

directly. Please, have patience as this takes some time. When the list has successfully been loaded, the First Time

Installation will be finished.

NOTE: The Fast Scan channel lists are maintained and updated automatically by the service list provider

and can’t be edited. Editing of channels can only be performed for channels which are saved above

channel number 4000 or additionally saved in favourite list(s). If you want to change to another

list you need to do a Factory Reset (see chapter 7.1.5 of the user manual on our website: www.

thomsonstb.net/downloads/manuals/THS813_UM_EN.pdf).

If the dish is pointed towards an incorrect satellite or if there is no signal or the signal from the satellite dish is

too low, the receiver cannot install channels and will go to the Main Menu. Please, first check the cables, the

alignment of the dish and the settings and try to setup again.

5.0 QUICK GUIDE TO USING YOUR RECEIVER

We at THOMSON understand that you can’t wait to enjoy your new HD receiver. The following quick guide will

make you familiar with the basic operation of this device. We do, however, advice you to read the full manual

on our website: www.thomsonstb.net/downloads/manuals/THS813_UM_EN.pdf to get the best performance

from your THOMSON HD receiver. To switch your receiver ON or to Standby, use the q button on the remote

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Thomson THS813 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info