Bedienungsanleitung Toolland FT92N (Seite 6 von 40) (Deutsch, Englisch, Holländisch, Französisch, Portugiesisch, Spanisch)

720267

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

FT92N

V. 05 – 04/07/2018 6 ©Velleman nv

8. Thermostatic Ignition

Prior to using the gas heater for the first time or after the gas heater has been stored for a

long time, we recommend, with the pressure regulator closed, repeatedly pressing the buttons

a few times.

Open the gas flow by turning the lever of the pressure regulator toward the marking.

Switching On the Gas Heater

 Fully turn the thermostat button in an anticlockwise direction until it reaches its maximum

position.

 Fully press the button for 15 seconds, and then press the button 2 or 3 times.

 The pilot light will burn. Repeat the steps above if the pilot light dies out.

 Keep pressing the button for 20 seconds to allow the thermocouple to heat. Release and

leave the thermostat button at its maximum position for 10 minutes. When the room has

reached the ideal temperature, turn the thermostat button in the desired position.

9. Cleaning and Maintenance

In the unlikely event of technical problems or should you need spare parts, please contact your

dealer.

 Periodic maintenance must be done by a qualified technician only.

 We recommend servicing your gas heater every two years by a qualified technician.

 Regularly check the pilot light, which must burn steadily.

 Check if the gas hose must be replaced. If so, contact your dealer for a new hose and

connect as described in chapter Starting the Gas Heater.

 We recommend cleaning your gas heater only with a closed pressure regulator, after the

gas heater has cooled down completely, and using non-abrasive cleaning agents.

 Store an unused gas heater in a dry and dust-free room, covered with a plastic sheet or

cloth.

10. Troubleshooting

The gas heater does not switch on.

 Check if the gas cylinder is filled with gas and if the pressure regulator is correctly

connected and opened.

 Make sure the gas hose is connected. Please follow the instructions correctly.

 Presence of air in the gas cylinder. Keep pressing the button until the pilot light burns and

the gas heater is switched on. Next, turn the thermostat button to the maximum position.

 The gas cylinder has been exposed to low temperatures. Apply hot and damp cloths to the

upper part of the gas cylinder to enhance the gasification and the normal gas output.

The gas heater switches off.

 If the gas heater switches off after the switch-on procedure, simply repeat the procedure

minding every step described in the instructions.

 If the gas heater switches off after 30 minutes of burning, it might be due to a little-

ventilated room. Air the room where the gas heater is being used and switch on the gas

heater.

 If the gas heater switches off within 30 minutes of burning, check for draughts and verify

the gas level in the cylinder.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Toolland FT92N Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info