Bedienungsanleitung Toolson KGZ4400 (Seite 15 von 180) (Alle Sprachen)

782350

Zoom out

Zoom in

Vorherige Seite

1/180

Nächste Seite

15 І 180

the ma chine is running; before performing tasks of

any kind release the main switch button located on the

handgrip, thus disconnecting the machine.

• Always keep hands away from the work area when

the machine is running; before performing tasks of

any kind release the main switch button located on the

handgrip, thus disconnecting the machine.

Assembly

WARNING! For your own safety, never connect the

plug to power source outlet until all assembly steps

are completed and you have read and understood

the safety and operational instructions.

Lift the saw from the packaging and place it on your work

bench.

Installing the Dust Bag (Fig. 2)

• Squeeze the metal collar wings 2 of the dust bag and

put it on the motor area exhaust port 1.

Setting the Tool

Note:

This tool is accurately adjusted before shipping from the

factory. Check the following accuracy and readjust if nec-

essary in order to obtain the best results in operation.

Installation of the Angle Fence at 90°, Fig. 3

1 Loosen the angle clamping lever (1).

2 Move the cutting head to the right until it rests against

the fence.

3 Tighten the angle clamping lever (1).

4 Test the saw blade with a 90° angle to the saw table.

If an adjustment is necessary, loosen the lock nut (2)

and position the socket screw in such a way that the saw

blade stands at 90° to the table. Re-tighten the lock nut.

5 Set the angle fence (3) with the screw at 0.

Installation of the Angle Fence at 45° Left. Fig.4

1 Loosen the angle clamping lever (1).

2 Move the cutting head to the left until it rests against

the fence.

3 Tighten the angle clamping lever (1).

4 Test the saw blade with a 45° angle to the saw table.

If an adjustment is necessary, loosen the lock nut and

position the socket screw (4) in such a way that the saw

blade stands at 90° to the table. Re-tighten the lock nut.

Installation of the Contact Surface,

• Lower the cutting head and push in the lock pin. Make

sure the table is in 0 mitre position.

• Place a combination square against the fence and

next to the saw blade.

• Loosen the two screws if the saw blade does not

touch the protractor.

• Adjust the fence so that the fence has full contact with

the square. Tighten the screws.

Connecting to the Power Supply

Check that the power supply and outlet used are in ac-

cordance with your mitre saw. Have a look at the rating

plate of the motor or the rating on the mitre saw. Any

changes should always be carried out by a qualied

aware of the risks involved in oerating the machine.

Any functional dis orders, especially those affecting the

safety of the machine, sholud terefore be rectied im-

mediately.

• Any other use exceeds authorization. The manufac-

turer is not responsible for any damages resulting from

un authorized use; risk is the sole responsibility of the

operator.

• The safety, work and maintenance instructions of the

manufacturer as well as the technical data given in

the calibrations and dimensions must be adhered to.

• Relevant accident prevention regulations and other,

gene rally recognized safety-technical rules must also

be adhered to.

• The machine may only be used, maintained, and op-

erated by persons familiar with it and instructed in its

operation and procedures. Arbitrary alterations to the

machine release the manufacturer from all responsi-

bility for any resulting damages.

• The machine may only be used with original accesso-

ries and tools made by the manufacturer.

Remaining hazards

The machine has been built using modern technolo-

gy in accor dance with recognized safety rules. Some

remaining hazards, how ever, may still exist.

• Only process selected woods without defects such

as: Branch knots, edge cracks, surface cracks. Wood

with such defects is prone to splintering and can be

hazardous.

• Wood which is not correctly glued can explode when

being processed due to centrifugal force.

• Trim work piece to a rectangular shape, center and

cor rectly secure before processing. Unbalanced work

pieces can be hazardous.

• Long hair and loose clothing can be hazardous when

the work piece is rotating. Wear personal protective

gear such as a hair net and tight tting work clothes.

• Saw dust and wood chips can be hazardous. Wear

per so nal protective gear such as safety goggles and

a dust mask.

• The use of incorrect or damaged mains cables can

lead to injuries caused by electricity.

• Even when all safety measures are taken, some re-

maining hazards which are not yet evident may still

be present.

• Remaining hazards can be minimized by following the

instructions in „Safety Precautions“, „Proper Use“ and

in the entire operating manual.

• Do not force the machine unnecessarily: excessive

cutt ing pressure may lead to rapid deterioration of the

blade and a decrease in performance in terms of nish

and cutting precision.

• When cutting aluminium and plastics always use the

app ro priate clamps: all workpieces must be clamped

down rmly.

• Avoid accidental starts: do not press the start button

while inserting the plug into the socket.

• Always use the tools recommended in this manual to

obtain the best results from your cutting-off machine.

• Always keep hands away from the work area when

Toolson KGZ4400 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info