Bedienungsanleitung Toolson KGZ4400 (Seite 17 von 180) (Alle Sprachen)

782350

Zoom out

Zoom in

Vorherige Seite

1/180

Nächste Seite

17 І 180

to climb up on the top of the workpiece, causing the

cutting head assembly and spinning blade to kick

back.

2. Never lower the spinning saw blade down before

pulling the cutting head to the front of the saw.

• Unlock the carriage 1 with the lock handle 2 and al-

low the cutting head assembly to move freely. (Fig. 6)

• Move the mitre handle and cutting head to the desired

mitre angle and bevel angle according to the mitre cut

and bevel cut procedures.

• Grasp the saw handle and pull the carriage forward

until the centre of the saw blade is over the front of

the work piece.

• Activate the switch, then press the blade guard lock

lever to lower the cutting head down.

• When the saw reaches full speed, push the saw han-

dle down slowly, cutting through the leading edge of

the workpiece.

• Slowly move the saw handle toward the fence, com-

pleting the cut.

• Release the switch and allow the blade to stop spin-

ning before allowing the cutting head to raise.

Depth adjustment normal Fig. 6.1

Sawing function 5 mm below the table top. (separate

work pieces.)

Depth stop (1) housing-adjacent.

Stop screw (2) is used.

Setscrew (3) has no function.

Depth adjustment variable Fig.

Sawing function above the table top. (covered cuts)

Set depth stop (1) to the outside.

Set the setscrew (3) to the desired measurement and se-

cure it with the counternut (4).

Make a test cut.

Stop screw (2) is not used.

Carrying the Tool

• Loosen the mitre lock knob and turn the table all the

way to the right. Lock the table at 45° mitre angle.

• Push the cutting head backwards and lock the car-

riage.

• Lower the cutting head and push in the lock pin.

• Carry this mitre saw with the built-in carry handle and

the side of the base.

Replacing of the saw blades, Fig. 7

Warning: Before replacing saw blades the switch

must be turned off and the mains plug must be dis-

connected from the mains socket in order to avoid

injuries by accidental start up of the machine.

• Disconnect the mains plug.

• Set the sawing unit to position “mitre operation”.

• Unlock the movable saw blade cover (7) by pressing

the blocker 3 (Fig. 1).

• When doing so lift the saw blade cover (7) to free the

saw blade (8).

• Push the saw blade blocker A (g. 7.1) until the saw

Compound Cut

• A compound cut is a combination of mitre cut and

bevel cut. Refer to the above procedures to perform

this cut.

Base Moulding

• Base moulding can be cut vertically against fence or

at on the table. Follow the table below for reference.

Settings Vertical position

(Back of moulding is

at against the fence)

Horizontal position

(Back of moulding is

at on the table)

Extension fence Close to the blade Far from the blade

Bevel angle 0° 45°

Moulding position Left side Right side Left side Right side

Inside

corner

Left

Rig

Left

Rig

Mitre

angle

Left at 45° Right at

45°

0° 0°

Moulding

position

Bottom

against

table

Bottom

against

table

Top

against

fence

Bottom

against

fence

Finished

side

Keep left

side of

cut

Keep right

side of

cut

Keep left

side of

cut

Keep left

side of

cut

Outside

corner

Left

Rig

Left

Rig

Mitre

angle

Right at

45°

Left at 45° 0° 0°

Moulding

position

Bottom

against

table

Bottom

against

table

Bottom

against

fence

Top

against

fence

Finished

side

Keep left

side of

cut

Keep right

side of

cut

Keep right

side of

cut

Keep right

side of

cut

Crown Moulding Cut

• Crown moulding can only be cut at on the table us-

ing this mitre saw.

• This mitre saw has special mitre stops of 31.6° left

and right and a bevel stop of 33.9° for a special crown

moulding 1 i.e. 52° between the back of the moulding

and the top at surface that ts against the ceiling; 38°

between the back of the moulding and the bottom at

surface that ts against the wall. Refer to the following

table for this crown moulding cut.

Settings Left side Right side

Inside corner Mitre angle 30° right 30° left

Bevel angle 33,9° 33,9°

Moulding

position

Top against

fence

Bottom against

fence

Finished side Keep left side

of cut

Keep left side

of cut

Outside corner Mitre angle 30° left 30° left

Bevel angle 33,9° 33,9°

Moulding

position

Bottom against

fence

Top against

fence

Finished side Keep right side

of cut

Keep right side

of cut

Note:

• These special stops cannot be used with 45° crown

moulding.

• Since most rooms do not have angles of exactly 90°,

ne tuning is needed and always take a test cut to

conrm the correct angles.

Pullover Cut

WARNING:

1. Never pull the cutting head assembly and spinning

blade towards you during the cut. The blade may try

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Toolson KGZ4400 Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info