Bedienungsanleitung Toolson KGZ4400 (Seite 18 von 180) (Alle Sprachen)

782350

Zoom out

Zoom in

Vorherige Seite

1/180

Nächste Seite

18 І 180

Check electrical connection cables regularly for damage.

Make sure the cable is disconnected from the mains

when checking.

Electrical connection cables must comply with the regu-

lations applicable in your country.

Single-phase motor

• The mains voltage must coincide with the voltage

specied on the motor’s rating plate.

• Extension cables up to a length of 25 m must have a

cross-section of 1.5 mm2, and beyond 25 m at least

2.5 mm2.

• The connection to the mains must be protected with

a 16 A slow-acting fuse.

Only a qualied electrician is permitted to connect the

machine and complete repairs on its electrical equip-

ment.

In the event of enquiries please specify the following

data:

• Motor manufacturer

• Type of current of the motor

• Data recorded on the machine’s rating plate

• Data recorded on the switch’s rating plate

If a motor has to be returned, it must always be dis-

patched with the complete driving unit and switch.

blade locks in place.

• Loosening of the saw blade xing screw with the pro-

vided socket wrench (B) (Attention, left-hand thread).

• Remove screw and saw blade ange.

• Remove the saw blade carefully. Attention: Danger of

injuries from the saw blade.

• Set the new saw blade on the inner saw blade ange

observing the correct size and rotational direction of

the saw blade.

• Attach the outer saw blade ange and tighten die

screw rmly.

• Set the saw blade cover back to the correct position.

Maintenance

WARNING: For your own safety, turn the switch off

and remove the plug from the power source outlet

before maintaining or lubricating your mitre saw.

General Maintenance

Occasionally use a cloth to wipe off chips and dust from

the machine. Oil the rotary parts once a month to extend

the tool life. Do not oil the motor.

Brush Inspection

Check the motor brushes after the rst 50 hours of use

for a new machine or after a new set of brushes have

been installed. After the rst check, examine them every

10 hours of use.

When the carbon is worn to 6 mm in length or if the

spring or shunt wire is burned or damaged, replace both

brushes. If the brushes are found serviceable after re-

moving, reinstall them.

Electrical connection

The installed electric motor is completely wired

ready for operation.

The customer’s connection to the power supply sys-

tem, and any extension cables that may be used,

must conform with local regulations.

Important remark:

The motor is automatically switched off in the event of

an overload. The motor can be switched on again after a

cool ing down period that can vary.

Defective electrical connection cables

Electrical connection cables often suffer insulation dam-

age.

Possible causes are:

• Pinch points when connection cables are run through

window or door gaps.

• Kinks resulting from incorrect attachment or laying of

the connection cable.

• Cuts resulting from running over the connecting cable.

• Insulation damage resulting from forcefully pulling out

of the wall socket.

• Cracks through aging of insulation.

Such defective electrical connection cables must not be

used as the insulation damage makes them extremely

hazardous.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Toolson KGZ4400 Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info