Bedienungsanleitung Toolson PRO-AS 360 (Seite 15 von 136) (Alle Sprachen)

782589

Zoom out

Zoom in

Vorherige Seite

1/136

Nächste Seite

15 І 136

Danger!

Sound and vibration

Sound and vibration values were measured in

accordance with EN 6074.

sound pressure level LpA 54.07 dB(A)

uncertainty KpA 3 dB

sound power level LWA 65.07 dB(A)

uncertainty KWA 3 dB

Wear ear-muffs.

The impact of noise can cause damage to hearing.

Total vibration values (vector sum of three directions)

determined in accordance with EN 60745.

Screwing without hammer action

Vibration emission value ah 0.265 m/s2

uncertainty K = 1,5 m/s2

The specied vibration value was established in

accordance with a standardized testing method. It may

change according to how the electric equipment is used

and may exceed the specied value in exceptional

circumstances.

The specied vibration value can be used to compare

the equipment with other electric power tools.

The specied vibration value can be used for initial

assessment of a harmful effect.

Keep the noise emissions and vibrations to a

minimum.

• Only use appliances which are in perfect working

order.

• Service and clean the appliance regularly.

• Adapt your working style to suit the appliance.

• Do not overload the appliance.

• Have the appliance serviced whenever necessary.

• Switch the appliance off when it is not in use.

• Wear protective gloves.

Before starting the equipment

Danger!

Be sure to read the following information before you put

the cordless screwdriver into operation:

1 Charge the battery only with the charging unit sup-

plied.

2 Only ever use screwdriver bits which are suitable for

the purpose and in faultless condition.

3 Before you begin to screw in walls and masonry,

check for concealed electric wiring, gas pipes and

water pipes.

Using

Charging the battery (Fig. 2)

The battery is protected from exhaustive discharge. An

integrated protective circuit automatically switches off

the equipment when the battery is at. In this case the

bit chuck will cease to turn.

Notice! Do not press the On/Off switch any more if the

protective circuit has tripped. This may damage the

battery.

Check that your mains voltage is the same as that

marked on the rating plate of the battery charger. Plug

the battery charger in the plug socket and connect the

40°C.

5 Do not keep the battery charger in places where the

temperature is liable to reach over 40°C. In particu-

lar, do not leave the battery charger in a car that is

parked in the sunshine.

6 Protect batteries from overheating! Overloads,

over-charging and exposure to direct sunlight will

result in overheating and cell damage. Never charge

or work with batteries which have been overheated

– replace them immediately if possible.

7 Storage of batteries, battery chargers and cord-

less tools. Store the charger and your cordless

tool only in dry places with an ambient temperature

of 10-40°C. Store your lithium-ion battery pack in a

cool, dry place at a temperature of 10-20°C. Protect

them from humidity and direct sunlight. Only place

fully charged batteries in storage (charged at least

40%).

8 Prevent the lithium-ion battery pack from freezing.

Battery packs which were stored below 0°C for more

than 60 minutes must be disposed of.

9 When handling batteries beware of electrostatic

charge: Electrostatic discharges cause damage of

the electronic protection system and the battery

cells. Avoid electrostatic charging and never touch

the battery poles!

When shipping or disposing of batteries and cord-

less tools, always ensure that they are packed in-

dividually in plastic bags to prevent short circuits

and res.

Do not lose these safety instructions.

Residual risks

Even if you use this electric power tool in ac-

cordance with instructions, certain residual risks

cannot be rules out. The following hazards may

arise in connection with the equipment’s construc-

tion and layout:

1. Lung damage if no suitable protective dust mask is

used.

2. Damage to hearing if no suitable ear protection is

used.

3. Health damage caused by hand-arm vibrations if the

equipment is used over a prolonged period or is not

properly guided and maintained.

Technical data

Motor power supply 3.6 V d.c.

Idling speed 200 min-1

Clockwise/counter-clockwise Yes

Battery charge voltage 6V d.c.

Battery charge current 600 mA

Charging unit supply voltage 100-240V ~

50-60 Hz

Charging time approx. 3 hours.

Battery capacity 1.5 Ah

Battery type Li-Ion

Weight 0.4 kg

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Toolson PRO-AS 360 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info