Bedienungsanleitung Toolson PRO-AS 360 (Seite 16 von 136) (Alle Sprachen)

782589

Zoom out

Zoom in

Vorherige Seite

1/136

Nächste Seite

16 І 136

The state of charge of the battery is displayed by illumi-

nating the appropriate LED lights. In order to activate

the display, the on/off switch (6) must be pressed.

All the LEDs are lit:

The battery is fully charged.

The yellow and red LEDs are lit:

The battery has an adequate remaining charge.

Red LED:

The battery is empty, recharge the battery.

Torque setting (Fig. 4 / Item 3)

The torque for a particular screw size is set with the

setting ring (3). The torque is dependent on a number of

factors:

• On the type and hardness of the material involved

• On the type and length of the screws used

• On the requirements that the screw connection has to

satisfy

The grating disengagement of the coupling indicates

that the selected torque level has been reached.

Notice! Only ever adjust the setting ring when the

equipment is at a standstill.

Changing the bit (Fig. 5)

Warning! Set the changeover switch to its center

position whenever you carry out any work (for example

changing the bit, maintenance , etc.) on the cordless

screwdriver.

• Pull back and hold the locking sleeve (10).

• Insert the bit (a) in the bit chuck (1) and let go of the

locking sleeve (10).

• Check that the bit is locked in placed by pulling on it.

Screws

It is advisable to use self-centering screws (e.g. Torx,

cross recessed head) as these will enable you to work

safely and reliably. Always make sure that the bit used is

of the same size and shape as the screw.

Maintenance

Danger!

Always pull out the mains power plug before starting any

cleaning work.

Cleaning

• Keep all safety devices, air vents and the motor

housing free of dirt and dust as far as possible. Wipe

the equipment with a clean cloth or blow it with com-

pressed air at low pressure.

• We recommend that you clean the device immediately

each time you have nished using it.

• Clean the equipment regularly with a moist cloth

and some soft soap. Do not use cleaning agents or

solvents; these could attack the plastic parts of the

equipment. Ensure that no water can seep into the

device. The ingress of water into an electric tool incre-

ases the risk of an electric shock.

Maintenance

There are no parts inside the equipment which require

additional maintenance.

charging cable to the charging connection. The charging

process starts as soon as the charging cable is connec-

ted to the charging adapter.

Recharging the battery (Fig. 1/2)

1. Connect the charger plug to the charging socket (5) of

the device.

2. Schließen Sie das Ladegerät (8) an eine Steckdose

an.

3. When the battery is fully recharged unplug the battery

charger (8) from the mains.

Battery charging

Battery fully charged

Notice! The handle may become a little warm during the

charging process. This is normal.

If the battery fails to charge, please check

• whether there is voltage at the socket outlet

• whether there is good contact at the charging contacts

of the charging unit

If the battery still fails to charge, send

• the charging unit

• and the screwdriver

to our customer service center.

Timely recharging of the battery will help it serve you

well for a long time. You must recharge the battery when

you notice that the power of the cordless screwdriver

drops.

Changeover switch (Fig. 3/Item 7)

The slide switch above the On/Off switch is for setting

the direction of rotation of the cordless screwdriver and

for preventing the cordless screwdriver from being swit-

ched on inadvertently. You can select between clockwi-

se and counterclockwise rotation. Change the direction

of rotation only when the equipment is at a standstill. If

you fail to observe this point, the gearing may become

damaged. When the slide switch is in the middle positi-

on, the On/Off switch is blocked.

On/Off switch (Fig. 3 / Item 6)

Press the On/Off switch to switch the cordless screwdri-

ver on. Release the On/Off switch again to switch it off .

LED lamp (Fig. 3/Item 2)

The LED lamp (2) can be used to additionally illuminate

the area where you want to drill or screw. The LED lamp

(2) will be lit automatically as soon as you press the On/

Off switch (6).

Checking the battery charge level (Fig. 1/4)

The battery’s charge level is indicated by the charge

state indicator (4).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Toolson PRO-AS 360 Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info