Bedienungsanleitung Toolson S-4-MINI (Seite 16 von 180) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

782277

Zoom out

Zoom in

Vorherige Seite

1/180

Nächste Seite

• Always keep hands away from the work area when the

ma chine is running; before performing tasks of any

kind release the main switch button located on the

handgrip, thus disconnecting the machine.

m Suitable use

To cut Fig. 4:

• With the saw blade (1) soft metal (aluminium, cop-

per, brass), single-sided coated sheet materials and

plastics.

• With the saw blade (2) hard and soft wood of domestic

or exotic origin, longitudinally and laterally through

the grain.

• With the cutting wheel (3) steel.

• With the diamond saw blade (4) tiles and stone.

Unsuitable use

Do not cut:

• Firewood, as well as all other material types that are

not listed, particularly food.

Start-up

Observe the safety notes in the operating instructions before

operating the machine.

REMOVAL OF PACKAGING

Remove the box used to protect the machine during

trans portion and keep it intact for future transportation

and storage.

ELECTRICAL CONNECTIONS

Check that the electrical system to which the machine is

connected is earthed in compliance with current safety

regulations and that the current socket is in perfect con-

dition.

The electrical system must be ﬁtted with a magnetother-

mal protective device to safeguard all conductors from

short circuits and overload.

The selection of this device should be in line with the

following electrical speciﬁcations of the machine stated

on the motor.

NOTE: Your plunge cut saw’s electrical system is equipped

with an undervoltage relay which automatically opens the

circuit when the voltage falls below a minimum pre-est-

ablished limit and which prevents the self-reset of ma-

chine functions when voltage returns to normal levels.

If the machine stops involutarily, do not be allarmed.

Make sure that there has not been a voltage failure in the

electrical system.

ADJUSTING

Caution: Prior to carrying out one of the following adjust-

ment steps, switch the machine off and unplug the mains

plug.

Cutting depth adjustment, Fig. 2

The cutting depth can be adjusted from 0 to 30,5 mm.

Unfasten the cutting depth adjustment screw (6) and set

the required depth using the scale (7) and retighten the

removing material with the edge of the wheel. Apply-

ing lateral force to these cutting-off wheels can cause

them to break.

• Do not used worn grinding/sanding wheels from larger

electric tools. Grinding/sanding wheels for larger elec-

tric tools are not designed for the higher speeds of

smaller electric tools and may break.

m Proper use

CE tested machines meet all valid EC machine guidelines as

well as all relevent guidelines for each machine.

• The machine must only be used in technically perfect

con dition in accordance with its designated use and

the in structions set out in the operating manual, and

only by safety-conscious persons who are fully aware of

the risks involved in oerating the machine. Any func-

tional dis orders, especially those affecting the safety of

the machine, sholud terefore be rectiﬁed immediately.

• Any other use exceeds authorization. The manufacturer

is not responsible for any damages resulting from un-

authorized use; risk is the sole responsibility of the

operator.

• The safety, work and maintenance instructions of the

manufacturer as well as the technical data given in

the calibrations and dimensions must be adhered to.

• Relevant accident prevention regulations and other,

gene rally recognized safety-technical rules must also

be adhered to.

• The machine may only be used, maintained, and op-

erated by persons familiar with it and instructed in its

operation and procedures. Arbitrary alterations to the

machine release the manufacturer from all responsi-

bility for any resulting damages.

• The machine may only be used with original accesso-

ries and tools made by the manufacturer.

m Remaining hazards

The machine has been built using modern technology in

accor dance with recognized safety rules. Some remaining

hazards, how ever, may still exist.

• The use of incorrect or damaged mains cables can lead

to injuries caused by electricity.

• Even when all safety measures are taken, some re-

maining hazards which are not yet evident may still

be present.

• Remaining hazards can be minimized by following the

instructions in „Safety Precautions“, „Proper Use“ and

in the entire operating manual.

• Do not force the machine unnecessarily: excessive

cutt ing pressure may lead to rapid deterioration of the

blade and a decrease in performance in terms of ﬁnish

and cutting precision.

• When cutting aluminium and plastics always use the

app ro priate clamps: all workpieces must be clamped

down ﬁrmly.

• Avoid accidental starts: do not press the start button

while inserting the plug into the socket.

• Always use the tools recommended in this manual to

obtain the best results from your plunge cut saw.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Toolson S-4-MINI Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info