Bedienungsanleitung Toolson TS6000 PRO (Seite 23 von 200) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Spanisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

782529

Zoom out

Zoom in

Vorherige Seite

1/200

Nächste Seite

23 І 200

Cutting narrow workpieces (Fig. 21)

Be sure to use a push stick (16) when making longitudi-

nal cuts in workpieces smaller than 120 mm in width. A

push block is supplied with the saw! Replace a worn or

damaged push stick immediately.

• Adjust the parallel stop to the width of workpiece you

require.

• Feed in the workpiece with two hands. Always use the

push stick (16) in the area of the saw blade.

• Always push the workpiece through to the end of the

splitter.

m Caution! With short workpieces, use the push stick

from the beginning.

Making cross cuts (Fig. 22)

- Slide the cross stop (13) into one of the grooves

(32a/32b) in the table and adjust to the required

angle. If you also want to tilt the blade (5), use the

groove (31a) which prevents your hand and the cross

stop from making contact with the blade guard.

- Press the workpiece rmly against the cross stop (13).

- Switch on the saw.

- Push the cross stop (13) and the workpiece toward

the blade in order to make the cut.

-Important:

Always hold the guided part of the workpiece.

Never hold the part which is to be cut off.

- Push the cross stop (13) forward until the workpiece is

cut all the way through.

- Switch off the saw again. Do not remove the offcut

until the blade has stopped rotating.

Making angular cuts (Fig.23)

Angular cuts must always be made using the parallel

stop (7).

- Set the blade (5) to the desired angle.

- Set the parallel stop (7) in accordance with the work-

piece width and height

- Carry out the cut in accordance with the workpiece

width

Cutting particle boards

To prevent the cutting edges from cracking when work-

ing with particle boards, you should not set the saw

blade (5) more than 5mm greater than the thickness of

the workpiece.

Transport

1. Before any transport, turn the power tool off and

disconnect it from the power supply.

2. At least two people are needed to carry the power

tool.

3. Protect the power tool from blows, impact and

strong vibrations, e.g. during transport in vehicles.

4. Secure the power tool against tilting and sliding.

5. Never use guards for handling or transport.

Transport without frame (Fig. 24)

1. Pull out the table width extension (14).

2. Tilt the machine to its wheels (32).

3. Hold on to the machine by the handle on the table

width extension (14) and pull it behind you.

Rip fence assembly (Fig. 16)

- Fix the rip fence (7) by placing it at the back and

pulling the locking lever (23) down.

- For disassembly, pull the locking lever up and remove

the rip fence (7).

- The locking force of the rip fence can be set with the

rear knurled nut.

Setting the cutting width (Fig. 17)

- The rip fence (7) must be used for lengthwise cutting

of wood.

- Place the rip fence (7) on the guide rail (12) to the

right or left of the saw blade.

- On the guide rail for the rip fence (12) there are 2 sca-

les (27/28) which display the gap between the fence

rail (25) and the saw blade (5).

- Set the rip fence (7) to the required specication on

the sight-glass (29) and secure it with the locking

handle for the rip fence.

Using the table width extension (Fig. 18)

- The table width extension (14) should always be used

for particularly wide work pieces.

- Loosen the locking handle (30) and pull out the table

width extension enough so the work piece can lie on it

without tilting.

Cross stop (Fig. 19)

- Push the cross stop (13) into a slot (31 a/b) on the

saw table.

- Loosen the locking handle (32).

- Rotate the cross stop (13) until the required angle is

set. The scale (33) shows the set angle.

- Re-tighten the locking handle (33).

Operation

Working instructions

After each new adjustment it is advisable to carry out a

trial cut in order to check the set dimensions. After switch-

ing on the saw, wait for the blade to reach its maximum

speed of rotation before commencing with the cut.

Secure long workpieces against falling off at the end of

the cut (e.g. with a roller stand etc.)

Take extra care when starting the cut!

Never use the equipment without the suction function.

Regularly check and clean the suction channels.

Making longitudinal cuts (Figure 20)

Longitudinal cutting (also known as slitting) is when you

use the saw to cut along the grain of the wood.

Press one edge of the workpiece against the parallel stop

(7) while the at side lies on the saw table (1). The blade

guard (2) must always be lowered over the workpiece.

When you make a longitudinal cut, never adopt a work-

ing position that is in line with the cutting direction.

- Set the parallel stop (7) in accordance with the work-

piece height and the desired width.

- Switch on the saw.

- Place your hands (with ngers closed) at on the

workpiece and push the workpiece along the parallel

stop (7) and into the blade (5).

- Guide at the side with your left or right hand (depend-

ing on the position of the parallel stop) only as far as

the front edge of the saw blade guard (2).

- Always push the workpiece through to the end of the

splitter (4).

- The offcut piece remains on the saw table (1) until the

blade (5) is back in its position of rest.

- Secure long workpieces against falling off at the end

of the cut (e.g. with a roller stand etc.) (e.g. roller table

etc.)

Toolson TS6000 PRO Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info