Bedienungsanleitung Topcom Babytalker 3100 - KS 4231 (Seite 8 von 72) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

484003

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

Babytalker 3500 SEDS

8.3 Connecting the Baby Unit to the AC Mains

Insert the small plug of the AC mains adapter in the mains power

connector of the baby unit and plug the AC mains adapter into a mains

connector (230 V / 50 Hz).

8.4 Installing Rechargeable Batteries in the Parent Unit

See Figure on the fold-out page.

– Rotate the belt clip upward.

– Turn the screw on the cover of the battery compartment at the back of

the parent unit 90° counterclockwise and remove the battery

compartment cover.

– Place the NiMH battery pack in the battery compartment.

Ensure that the tab of the battery pack fits in the corresponding recess

and that the polarity matches the figure (B).

– Carefully close the battery compartment and rotate the belt clip back

downward.

8.5 Installing the Parent Unit charging cradle

– Insert the small plug of the AC mains adapter in the mains power connector of the charging station and

plug the AC mains adapter into a mains connector (230 V / 50 Hz).

– Place the parent unit in the charging station. The red Charging LED will go on.

9 Operation and Use

9.1 Switching the Baby Unit and Parent Unit On and Off

– Press the On/Off switch to switch on the parent unit. The power LED will lit.

– Press the On/Off switch to switch on the baby unit. The power LED will lit.

– Press the On/Off switch to switch on the parent unit. The power LED will go out.

– Press the On/Off switch to switch off the baby unit. The power LED will go out.

9.2 Checking the Link Between the Parent Unit and the Baby Unit

You should always check the wireless link when you use the babyphone for the first time.

– Put the parent unit in the same room as the baby unit, separated by at least two metres.

– Switch on both devices. The parent unit will try to establish a connection with the baby unit.

– The green Link LED on the parent unit blinks while it is trying to establish a connection.

If NEMo mode is turned OFF (see “9.4 NEMo Switch Setting”): The LED stays on continuously

after a connection has been established.

If NEMo mode is turned ON: The green link LED on Parent Units will flash until they communicate.

Once the link is established, the LED will light continuously. After a while, when the baby unit doesn’t

capture any sound, the LED will flash every 5 seconds because the baby unit stops the transmission.

CAUTION

• The mains connector must be within easy reach so you can

quickly unplug the power cable in an emergency.

• Use only the supplied AC mains adapter (6 V DC / 300 mA).

CAUTION

• Use only the supplied NiMH battery pack in the parent unit.

• Do not turn the screw past the ‘Open’ point.

• It takes around 10 hours to fully charge the batteries.

• The parent unit will try to establish a connection with the baby unit. If the Link LED goes

on, a connection has been established. If it does not, see below.

SEDS

LONG

ECO

6V/300mA

90° MAX

OPEN

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Topcom Babytalker 3100 - KS 4231 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info