Bedienungsanleitung Topcom butler 131 (Seite 19 von 33) (Deutsch, Englisch, Holländisch, Französisch)

299622

Zoom out

Zoom in

Vorherige Seite

1/33

Nächste Seite

34 35

5 BATTERY

Open the cover of the battery compartment on the back of the handset. Place

the 2 rechargeable NiCd batteries (1,2V/600mAh) in the battery compartment

and close the compartment again afterwards.

For the first use, the batteries need to be fully charged before the telephone can

be used. Put the handset on the connected base station to charge the battery.

The battery indicator on the base unit lights to indicate that the battery is being

charged. After approximately 14 hours the battery is fully charged.

Do not put the handset back on the base station, every time the phone has been

used. Put the handset only on the base when it is indicated that the battery is

almost empty. It is better for the battery to be sufficiently discharged before

being charged again. You will hear an intermittent warning tone and the Battery

indicator on the display of the handset will blink.

A fully charged battery allows a talk time of 6 hours. In standby mode the battery

has to be recharged after approximately 60 hours .

Remarks

• The charger contacts of the handset should not come into contact with metal since this

could cause a short-circuit and damage the batteries irreparably.

• The charger contacts on the base station and on the handset should be cleaned with a

soft cloth once a month.

• If you do not use your unit for a longer period of time, do not put the handset in

charging position on the base station. It is better for your batteries not to do so. The best

way is to remove your batteries during that time.

• Do not throw faulty batteries just anywhere, they are small chemical waste and have to

be treated as such.

6 OPERATION

6.1 Out of range warning

Obstacles between the handset and the base station will influence the operation

range. When the handset is too far away from the base station, the quality of the

connection will deteriorate and you will hear a warning tone. The communication

will be broken automatically if you do not go back into the operation range with-

in 10 seconds.

If a connection between the handset and the base station is not possible, you will

hear an intermittent warning tone.

6.2 Making a telephone call

6.2.1 Normal dialling

Press the Line button. When the radio connection has been established, you hear

a short beep. The radio connection indicator on the base station lights up and on

the handset the radio connection indicator will appear on the display

Now the desired telephone number can be dialled. The duration of the call is

visible on the display. Press the Off button to end the conversation or put the

handset back on the base unit.

6.2.2 Block dialling

It is possible to first dial the number and then push the Line button. This way the

caller can check whether the entered number is correct or not. If he has entered a

wrong number, he can erase it by using the Mute button. After that, push the

Line button to call the number.

• Only 3 seconds after taking the line, the number is being sent out.

• To end the conversation, press the Off button or put the handset back on the

base station.

• The duration of the call is visible on the display (format HH-MM-SS).

6.3 Receiving a telephone call

When the base station receives a call, it will start to ring and passes the call on to

the handset. The handset will also ring when it is not lying on the base station. If

the handset is lying on the base unit, you will only hear the ringing signal of the

base station.

When the base station receives a call and the handset is lying on the base station,

you will immediately be connected to the caller when you pick up the handset

(this function can be activated/deactivated, see 9. Settings).

Press the Stop button to end the communication after the conversation or put the

handset back on the base station. The call time appears on the display.

6.4 Receiver volume control

When you do not hear your caller loud enough, you can adjust the speaker

volume by pressing the Line button.

• Hi = high

• Lo = low

Butler 131/136 Butler 131/136

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Topcom butler 131 Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info