Bedienungsanleitung Tormatic PowerSwing (Seite 9 von 20) (Deutsch, Englisch, Holländisch)

710114

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

PowerSwing

ENGLISH

Guide for the installer

Page 9

11. Release the operator (see paragraph 5) and manually check

if the gate can completely open without hindrances and stop

at the mechanical travel stops as well as if the leaf moves

regularly without any friction.

12. Carry out the necessary corrective measures and repeat from

point 8.

13. Temporarily release the operator from the front bracket and

weld the bracket definitively.

If the leaf structure does not allow a bracket welding, the

suitable bracket to screw (optional) can be used together

with suitable fastening systems (Fig.13). Then carry out the

same operations as prescribed for the bracket to weld.

We recommend to grease all the fastening pins of the fittings.

3.5. WIRING THE OPERATOR

A terminal board is fitted in the lower part of the operator for the

connection of the motor, of any limit switch and for the earthing

of the operator.

For the connections should be usable a sheathed cable sui-

table for mobile installation outdoor.

Motor wiring operations:

1. Open one of the two pre-drilled holes in the supplied cover,

Fig.14; in case of operators with limit switches, open both

holes.

2. Fit the supplied cable gland.

3. Connect the motor and the earthing with reference to Fig.15

and the following tables.

PowerSwing

Pos. Colour Description

Blue (White)

Common cable

Brown (Red)

Phase 1

Black (Black)

Phase 2

T Yellow/Green (Green)

Earthing

4. Close the cover with the four supplied screws, Fig.16.

3.6. START-UP

Cut power before any job on the system or on the operator,

togliere l’alimentazione elettrica.

Carefully observe points 10, 11, 12, 13 and 14 of the SAFETY

GENERAL RULES.

With reference to the indications in Fig.3, set the ducts and carry

out the electrical connections of the control board and of the

chosen accessories.

Always separate power cables from control and safety cables

(push button, receiver, photocells, etc.). To avoid any electrical

noise whatever in the unit, use separate sheaths.

1. Power up the system and check the LED condition as shown

in the table of the control board instructions.

2. Program the control board according to the needs by following

the given instructions.

4. TESTING THE AUTOMATED SYSTEM

• Carefully check operating efficiency of the automated system

and of all accessories connected to it, paying special attention

to the safety devices.

• Hand the “User’s Guide” to the final user together with the Main-

tenance sheet.

• Explain correct operation and use of the automated system to

the user.

• Indicate the potentially dangerous areas of the automated

system to the user.

5. MANUAL OPERATION

If the automated system needs to be moved manually due to a

power lack or to an operator malfunction, proceed as follows:

1. Cut power by means of the safety circuit breaker (even in the

event of a power lack).

2. Slide the protective cap, Fig.22/a.

3. Insert the key and turn it 90°, Fig.22/b.

4. Lift the control lever, Fig.22/c.

5. To release the operator turn 180° the control lever to the direc-

tion indicated by the arrow on the release system, Fig.22/d.

6. Open and close the leaf manually.

To hold the operator in manual operation the release device

should be left in its current positions and the system should

be without power.

5.1. RESTORING NORMAL OPERATION

To restore normal operating conditions, proceed as follows:

1. Ensure that the system is not powered.

2. Turn the release system 180° in the opposite direction of the

arrow.

3. Turn 90° the release key and remove it.

4. Close the control lever and the protection cover.

5. Power up the system and perform some movements in order

to check the correct restoring of every function of the auto-

mated system.

6. MAINTENANCE

In order to ensure correct operation and constant safety over time,

make a general check of the system every six months, paying

special attention to the safety devices. In the booklet “User gui-

de”, a form has been prepared for the recording of maintenance

operations.

7. REPAIRS

The user must not carry out any repairs or maintenance operations;

these must be effected only and exclusively by qualified service

centres.

8. AVAILABLE ACCESSORIES

For the available accessories see the TORMATIC

catalogue.

9. SPECIAL APPLICATIONS

Applications other than those described in the present manual are

EXPRESSLY FORBIDDEN.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Tormatic PowerSwing Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info