710112

Tormatic RUN 500 Accu - Set Seite 18

18
Zoom out
Zoom in
Vorherige Seite
1/47
Nächste Seite
19
GB
Retain these installation, operating and maintenance instructions for the full duration of the operator’s service life!
• Install the solar module
Use only the manufacturer's originalsolar
modules.
Reliable operation can only be ensured if sufficient
energy is supplied also in winter when there is little
sunshine. Therefore, install the solar module
vertically towards south.
Install themounting bracket
Wall installation
Mark, drill and fasten the mounting bracket with
screws. Install the solar moduleand fix it with screws.
Roof installation
Install the mounting bracket.
Do not drill holes into the garage roof.
! Avoid leaks.
A flagstone, e.g., makes a good base. Bore holes in
the flagstone and fasten the bracket. Place on the
garage door and align south.
Electrical connection
Use a cable suitable for outdoor installation
or lay a cold-resistant PVC cable in conduit 4a
Connection. Mind correct polarity 4b.
! The battery has an internal 20 A blade-type
fuse. Charge. Function control incremental
display 4c.
• Dismantling the operator
1. Pull out the mains plug and disconnect all existing
terminals.
2. Disconnect door and operator. Fix door.
3. Proceed according to points3 to 13 of the
installaton Instructions but in reversesequence.
• Programming the operator
Control elements
The controls for programming the door operator are
protected by a transparent cover. The transparent
cover can be opened with a screwdriver. After the
operator has been programmed, the transparent
cover must be closed again.
A.Numerical display shows the menu stage as well
as the selected value.
a. Incremental display, indicates the power being
supplied by the solar moduleand flashes to
acknowledge taught handheld transmitter codes.
B.Button during the setting / adjustment phase
serves as an “up” buttonand outside the menu as
a start button.
C.Button during the setting /adjustment phase
serves as a “down” button.
D.Button is used to call up the setting/adjustment
menu, to change the menustages and to store the
settings.
The programming of the control unit is menu-driven.
By pressing button , the menu guide is called up.
The numbers displayed indicate the menu stage.
After approx. 2 seconds, the display flashes and the
setting can be altered via buttons and . The
selected setting is stored with button . And the
programme jumps automatically to the next menu
stage. By repeatedly pressing button , menu
stages can be skipped. To quit the menu, press
button until “0” is shown again. Outside the menu,
button can be used to generate astart impulse.
Before programming
- Allow doorto engage into the carriage.
- Connect theAccu-Pack drive. Light turns on.
- Observe the hand transmitter instructions.
1
2
3
4
14
Menu stage 1: Programming the start
function forthe hand transmitter
Briefly press button . “1” is displayed. As soon as
the display flashes, press and keep pressed for
approx. 1 second the button of the hand transmitter,
with which you later wish to start the operator. As
soon as the code has been read, the red point
display (a) flashes four times before quitting. Figure
0 will be displayed. Menufinished.
Further hand transmitters (up to a maximum of 10)
can be programmed.
Menu stage 2: Programming the light
function forthe hand transmitter
Press key briefly and figure 1will be displayed.
Press key once again and figure 2 will be
displayed.
Press the second button at the transmitter with which
the 4-min light is to be switched on. As soon as the
code has been read in, the red point display (a) will
flash four times to acknowledge the entry. Figure 0
will be displayed. Menu finished.
Deleating all the hand transmitters programmed
for theoperator:
Plug in the operator‘s main plug while pressing
button .
Menu stage 3: Setting/adjusting the top end-
of-travel position
Keep button pressed for 3 seconds. Number 3
appears in the display 17a.
Wait a short while until the 3 startsflashing.
Press button and make sure that the door travels in
the OPEN direction.
!
If the door closes in the wrong direction, after
having pressed , keep button pressedfor
another 3 seconds. “3” flashesbriefly. The
travelling direction is altered.
Now travel by pressing button into the desired door
end position OPEN 17b.
By pressing button , the position can be corrected
into direction CLOSE.
Once the desired OPEN end-of-travel position has
been reached, press button . The operator stores
the OPEN end-of-travel position and “4” appears in
the display.
Menu stage 4: Setting/adjusting the bottom
end-of-travel position
Wait a short while until “4” starts flashing.
Press button . The operator causes the door to
travel in the CLOSE direction as long as the button is
pressed. The position can be altered to the OPEN
direction via button ..
Once the desired CLOSE end-of-travel position has
been reached, press button . The operator stores
the CLOSE end-of-travel position and “0” appears in
the display.
Force-learning cycle
!
We recommend setting the suitable door type in
menu stage 8 prior tothe force-learning cycle.
During this opening and closing cycle, the
operator learns the force required to open and close
the door. The cyclesA force limit does not apply!
must not be interrupted. During these cycles must
not be interrupted. During these cycles “0” appears
in the display.
- Press button . The operator causes the door to
open until the top end-of-travelposition has been
15
16
17
18
19
reached.
- Now pressbutton again. The operator causes
the door to close untilthe bottom end-of-travel
position has been reached.
- After approx. 2 seconds, “0”disappears.
Caution! If the force setting is too high, persons may
be placed at risk ofinjury.
The factory setting is 4!
Checking theforce limit facility
- Place anobstruction (e. g. operator’s cardboard
box) underneath the doors’s closing edge.
- Starting from theOPEN end-of-travel position,
actuate the door to close.
- The door travelstowards the obstruction, stops
and travels back to thetop end-of-travel position.
If the door springs have been changed or altered,
then the force learning cycle must be repeated:
proceed to menu stage 5 and keep button
pressed for 3 seconds. “0” appears in the display.
Then complete the force learning cycle as explained
under point 19.
20
… 18 …

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Tormatic RUN 500 Accu - Set wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info