Bedienungsanleitung Tormatic RUN 500 Accu - Set (Seite 20 von 47) (Deutsch, Englisch, Holländisch, Französisch, Spanisch)

710112

Zoom out

Zoom in

Vorherige Seite

1/47

Nächste Seite

Retain these installation, operating and maintenance instructions for the full duration of the operator’s service life!

• Operating Instructions

These Operating Instructions describe how to use

the prodct properly and safely. The safety advice and

information as well as the accident prevention and

general safety regulations for the field of application

must be complied with.

All personsusing the gate system

must be shownhow to operate it

properly and safely.

Keep handtransmitters out of the reach

of children.

When theoperator is being used, the

opening andclosing phases must be

monitored. Itmust be ensured that

neither personsnor objects are located

within thegate’s range of travel.

• Normal operation

The garage door operator can be actuated by an

impulse generator such as hand transmitter, key

switch etc. It is only necessary to generate a short,

sharp impulse.

Functional sequence

First impulse:

Operator starts up and causes the door to travel to

set open or closed travellimits.

Impulse generated while door is moving:

The door stops.

Repeated impulse:

Door continues to move butin opposite direction .

• Quickrelease

During adjustments, in the event of a power failure or

malfunctions, the door can be disengaged from the

operator by actuating the pull cord on the carriage

and then be operated manually.

If the door is to be operated manually over a longer

period of time, then the existing locking pin must be

inserted (see figure ). The door latches put out of12

service for power operation must be refitted,

otherwise the door is not latched in the the closed

position.

In order to restore power operation, return the

locking pin to the parking position ( ) and put thea

latches out of service.

After an impulse has been generated, the door

automatically latches with the dooroperator.

• Internal safety device

If the closing door encounters an obstruction, the

operator stops and causes the door to open to ist top

end-of-travel position in order to clear the

obstruction. During the last 2 seconds of the closing

cycle, the door only opens slightly, this being

sufficient to clear the obstruction but otherwise

preventing anyone from taking a look into the

garage.

If the opening door encounters an obstruction, the

operator stops immediately and reverses the

travelling direction for approx. onesecond.

• External safety device

Connection plan ( figure )13

Wicket door contact STOPA

An open wicket door stops the operator immediately

or prevents it from starting up.

• Solar mode

Make sure that there are no shadows from plants,

trees or buildings.

Remove dirt and leaves, and snow in winter, from the

module.

Check the drive display:

Flash Solar power IL

__________________________________

1 s 300 mA - 1 A

2 s 30 mA - 300 mA

4 s 3 mA - 30 mA

60 s 0 - 3 mA

• Maintenance / Checks

The doorsystem must be inspected

and testedby a specialist company

prior toinitial operation and at least

once ayear thereafter.

Monitoring theforce limit

The operator control unit features a dual-processor

safety system to monitor the force limit.

The integral force cut-out is automatically tested at

each travel limit.

The door system must be checked prior to initial

operation and at least once a year thereafter. In the

process, the force limiting device (figure 20) must be

tested!

Caution! If the closing force is set too

high, persons can be placedat risk of

injury or property could sustaindamage.

Tthe force limit for the opening cycle can be adjusted

in menu stage 5, the force limit for the closing cycle

can be adjusted in menustage 6.

• Cycle counter

The cycle counters stores the number of opening or

closing cycles performed by theoperator.

In order to read out the meter, keep the

button pressed for 3 seconds until a number is

displayed. The display throws out the values

beginning from the highest decimal place down to

the lowest one after another. In the end, a horizontal

line is displayed. Example: 3456cycles, 3 4 5 6 -

• Accu-Pack

The battery is maintenance-free.

Light barrier (STOP B)

An interruption of the light barrier causes a stopping

and a reversal during the closing cycle. An

interruption of the light barrier during the opening

cycle makes no difference.

• Lighting

The lighting switches on automatically whenever a

start impulse is generated and switches off again

after the set time phase (factory setting approx. 60

seconds).

• Handtransmitter

Programming further hand transmitters:

See menu stages 1 and2 (figure 15 and 16).

• Battery mode

Recharge theAccu-Pack

Recharge theAkku-Pack before the first start-up and

after extended periods of no use. Charge the Accu-

Pack only with the supplied wall wart (power

adapter).

Insert the plug in theAccu-Pack socket.

Mind display:

LED red: Accu-Pack is being charged

LED blue: Accu-Pack is fully charged, trickle

charge.

Do not stop charging unless the battery pack

! is fully charged.

Connecting the drive to the Accu-Pack

Insert the drive plug in theAkku-Pack socket so that it

latches.

The drive is ready forimmediate use.

The charge of the Accu-Pack is sufficient for 40 days

with 4 openings a day. The charge is depleted earlier

in extreme temperatures.

Example: The charge drops to 50% at -10°C.

Exhaustion is a cause of early battery failure.

! Extended times of no-use of 6 months or more

deplete the battery.

Check the battery charge regularly and recharge in

time. We recommend the installation of a solar

module for easy recharging and extending the

battery life.

The battery charge is displayed every time the drive

is started:

Display Horn Battery charge

________________________________________

Continuous Charge voltage too high

tone

9 and 8 - Fully charged battery

7, 6, 5, 4 - Mean charge

3 1x briefly 30%, recharge

2 2x briefly 20%, urgent recharge

1 3x briefly 10%, operator can stop

0 Xx briefly <5%, no response from drive

!Have system examined by a specialist

Light is flashing

Disconnecting the Accu-Pack from the drive

Press in the lever at the Accu-Pack socket and pull

the plug.

Tormatic RUN 500 Accu - Set Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info