Bedienungsanleitung Torqeedo Cruise 3.0 FP (Seite 72 von 92) (Deutsch, Englisch)

807535

Zoom out

Zoom in

Vorherige Seite

1/92

Nächste Seite

DE EN

NOTE! For further information on the component and mounting, please refer to

the relevant operating manual.

6.8 Operation with external batteries

DANGER

Danger of injury or death due to improper installation. This can result in sever

injuries or death.

• All national laws and regulations must be observed during installation.

WARNING

Danger of injury due to overheating. This can result in moderate or severe

bodily injuries.

• Only use original Torqeedo cable sets.

• Power cables may only be extended with Torqeedo cable extensions.

• Do not connect any other loads to the power cables.

NOTE! External batteries may only be installed by qualied persons.

Observe the following points when using external batteries:

1. Use the cable set with eyelets of the Cruise 6.0 motor for the connection to

a current bus bar of your battery bank.

2. For direct connection to your battery bank, use the cable set with battery

pole terminals of the Cruise 3.0 motor.

3. If you use lead batteries (gel/AGM), we recommend batteries with at least

150 Ah per battery. For connection and wiring of the batteries, see connec-

tion diagram.

4. Always use a separate battery/battery bank for external loads.

5. Installing systems with external batteries may only be carried out by a

specialist in compliance with all national regulations (such as ISO 16315 or

ABYC E-11).

6. Lay the cables according to your plans and x them in the designated

places.

7. Connect the motor’s cable set to the boat's power bus bar, observing the

requirements for circuit protection, see connection diagram.

NOTE! For further information on the component and mounting, please refer to

the relevant operating manual.

6.9 Installation and wiring checklist

NOTE! Make sure that the battery main switch is in the “Off” position.

NOTE! Do not start the system test until you have ensured the following points:

Motor

• Mounting ange correctly mounted, fastened and sealed.

• Sealant fully cured.

• Motor correctly xed in the mounting ange.

• Locking ring on the shaft tube correctly tted.

• Propeller mounted.

• Galvanic anodes mounted.

• Correct polarity of the power cables in the plug housing.

Battery main switch

• Main switch mounted and splash-proof.

• Installation position adhered to.

• Main switch in “Off” position.

Batteries (Torqeedo)

• Batteries installed so that they are splash-proof, fastened and/or secured

against slipping.

Other components

• Other components installed according to specications.

Wiring

• Connect all data cables to the components according to the respective

connection diagram.

• Connect all power cables to the components according to the respective

connection diagram.

• Power cable connected to components in correct polarity.

• All cables laid tension- and load-free.

• All cable abrasion points eliminated.

• Cable plug of the power cables correctly connected.

• All cable ties cut off without burrs.

• Excess data cables coiled up and fastened.

• Excess power cables xed and not coiled.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Torqeedo Cruise 3.0 FP Seite 72

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Torqeedo Cruise 3.0 FP

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info