Bedienungsanleitung Toshiba 48L1863 (Seite 13 von 31) (Englisch)

681971

Zoom out

Zoom in

Vorherige Seite

1/31

Nächste Seite

English - 12 -

Switching On/Off

To Switch the TV On

Connect the power cord to a power source such as a

wall socket (220-240V AC, 50 Hz).

To switch on the TV from standby mode either:

• Press the Standby button, Programme +/- or a

numeric button on the remote control.

• Press the middle of the side function switch on the

TV in.

To Switch the TV Off

Press the Standby button on the remote control or

press the middle of the side function switch on the

TV in and hold it down for a few seconds, the TV will

switch into standby mode.

To power down the TV completely, unplug the

power cord from the mains socket.

Note: When the TV is switched into standby mode, the standby

LED can blink to indicate that features such as Standby

Search, Over Air Download or Timer is active. The LED can

also blink when you switch on the TV from standby mode.

First Time Installation

Note: If you are going to perform FRANSAT installation, insert

the FRANSAT card (optional) into the Conditional Access

terminal of your TV before switching on your TV.

When turned on for the first time, the language

selection screen is displayed. Select the desired

language and press OK. In the following steps of

the installation guide, set your preferences using the

directional buttons and OK button.

On the second screen set your country preference.

Depending on the country selection you may be asked

to set and conrm a PIN at this point. The selected PIN

cannot be 0000. You have to enter it if you are asked

to enter a PIN for any menu operation later.

Note: M7(*) operator type will be dened according to the

Language and Country selections that you made in the First

Time Installation.

(*) M7 is a digital satellite service provider.

You can activate Store Mode option in the next step.

This option will congure your TV’s settings for store

environment and depending on the TV model being

used, the supported features of it may be displayed on

the side of the screen as an info banner. This option

is intended only for store use. It is recommended to

select Home Mode for home use. This option will be

available in Settings>System>More menu and can

be turned off/on later. Make your selection and press

OK to continue.

On next screen you can set broadcast types to be

searched, set your encrypted channel searching

and time zone (depending on the country selection)

preferences. Additionally you can set a broadcast

type as your favourite one. Priority will be given to the

selected broadcast type during the search process

and the channels of it will be listed on the top of the

channel list. When nished, highlight Next and press

OK to continue.

About Selecting Broadcast Type

To turn a search option for a broadcast type highlight

it and press OK. The checkbox next to the selected

option will be checked. To turn the search option off

clear the checkbox by pressing OK after moving the

focus on the desired broadcast type option.

Digital Aerial: If D. Aerial broadcast search option

is turned on, the TV will search for digital terrestrial

broadcasts after other initial settings are completed.

Digital Cable: If D. Cable broadcast search option

is turned on, the TV will search for digital cable

broadcasts after other initial settings are completed.

A message will be displayed before starting to search

asking if you want to perform cable network search. If

you select Yes and press OK you can select Network

or set values such as Frequency, Network ID and

Search Step on the next screen. If you select No

and press OK you can set Start Frequency, Stop

Frequency and Search Step on the next screen.

When nished, highlight Next and press OK button

to continue.

Note: Searching duration will change depending on the

selected Search Step.

Satellite(**): If Satellite broadcast search option

is turned on, the TV will search for digital satellite

broadcasts after other initial settings are completed.

Before satellite search is performed some settings

should be made. A menu will be displayed where you

can select to start M7 or Fransat operator installation

or a standard installation.

To start an M7 operator installation set the Install Type

as Operator and the Satellite Operator as the related

M7 operator. Then highlight Preferred Scan option

and set as Automatic channel scan and press OK

to start the automatic search. These options can be

preselected depending on the Language and Country

selections that you made in the earlier steps of the rst

time installation process. You may be asked to select

HD/SD or country specic channel list according to

your M7 operator type. Select one and press OK to

proceed.

Wait till the scan is nished. Now the list has been

installed.

While performing an M7 operator installation, if you

want to use the satellite installation parameters that

differ from the default settings select the Preferred

Scan option as Manual channel scan and press the

OK button to proceed. Antenna Type menu will be

displayed next. After selecting the antenna type and

the desired satellite in the following steps press OK

in order to change the satellite installation parameters

in the sub-menu.

Toshiba 48L1863 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Toshiba 48L1863

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info