Bedienungsanleitung Toshiba 48L1863 (Seite 14 von 31) (Englisch)

681971

Zoom out

Zoom in

Vorherige Seite

1/31

Nächste Seite

English - 13 -

To start a Fransat installation set the Install Type as

Operator and then set the Satellite Operator as the

related Fransat operator. Then press the OK button

to start Fransat installation. You can select to start an

automatic or manual installation.

Press OK to proceed. Fransat Installation will be

performed and broadcasts will be stored (if available).

If you set the Install Type as Standard, you can

continue with regular satellite installation and watch

satellite channels.

You can start a Fransat installation at any time later

from the Settings>Installation>Automatic channel

scan> Satellite menu.

In order to search for satellite channels other than

M7 or Fransat channels you should start a standard

installation. Select the Install Type as Standard and

press the OK button to proceed. Antenna Type menu

will be displayed next.

There are three options for antenna selection. You can

select Antenna Type as Direct, Single Satellite Cable

or DiSEqC switch by using Left or Right buttons.

After selecting your antenna type press OK to see

the options to proceed. Continue, Transponder list

and Congure LNB options will be available. You can

change the transponder and LNB settings using the

related menu options.

• Direct: If you have a single receiver and a direct

satellite dish, select this antenna type. Press OK to

continue. Select an available satellite on the next

screen and press OK t o scan for services.

• Single Satellite Cable: If you have multiple

receivers and a single satellite cable system, select

this antenna type. Press OK to continue. Congure

settings by following instructions on the next screen.

Press OK to scan for services.

• DiSEqC switch: If you have multiple satellite dishes

and a DiSEqC switch, select this antenna type. Then

set the DiSEqC version and press OK to continue.

You can set up to four satellites (if available) for

version v1.0 and sixteen satellites for version v1.1

on the next screen. Press OK button to scan the rst

satellite in the list.

(**) If this feature is supported by your TV

Analogue: If Analogue broadcast search option is

turned on, the TV will search for analogue broadcasts

after other initial settings are completed.

A dialogue screen asking to activate parental control

will be displayed. If you select Yes, parental restriction

options will be displayed. Congure as desired and

press OK when nished. Select No and press OK

to advance, if you don’t want to activate parental

restrictions.

After the initial settings are completed TV will start

to search for available broadcasts of the selected

broadcast types.

While the search continues current scan results will

be displayed at the bottom of the screen. After all the

available stations are stored, Channels menu will be

displayed. You can edit the channel list according to

your preferences using the Edit tab options or press

the Menu button to quit and watch TV.

While the search continues a message may appear,

asking whether you want to sort channels according

to the LCN(*). Select Yes and press OK to conrm.

(*) LCN is the Logical Channel Number system that organizes

available broadcasts in accordance with a recognizable

channel number sequence (if available).

Notes:

To search for M7 channels after the First Time Installation,

you should perform the rst time installation again. Or press the

Menu button and enter the Settings>Installation>Automatic

channel scan>Satellite menu. Then follow the same steps

mentioned above in the satellite section.

Do not turn off the TV while initializing rst time installation.

Note that, some options may not be available depending on

the country selection.

Using Satellite Channel Table Feature

You can perform these operations using the Set-

tings>Installation>Satellite Settings>Satellite

Channel Table menu. There are two options regarding

to this feature.

You can download or upload satellite channel table

data. In order to perform these functions a USB device

must be connected to the TV.

You can upload current services and related satellites

& transponders in TV, to a USB device.

Additionally you can download one of the satellite

channel table les stored in USB device, to the TV.

When you select one of these les, all services and

related satellites and transponders in the selected

le will be stored in the TV. If there are any installed

terrestrial, cable and/or analogue services, they will

be kept and only satellite services will be removed.

Afterwards, check your antenna settings and make

changes if necessary. An error message stating “No

Signal” may be displayed if the antenna settings are

not congured properly.

Media Playback via USB Input

You can connect 2.5” and 3.5” inch (HDD with external power

supply) external hard disk drives or USB memory stick to your

TV by using the USB inputs of the TV.

IMPORTANT! Back up the les on your storage devices

before connecting them to the TV. Manufacturer will

not be responsible for any le damage or data loss.

Certain types of USB devices (e.g. MP3 Players)

or USB hard disk drives/memory sticks may not be

compatible with this TV. The TV supports FAT32 and

Toshiba 48L1863 Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Toshiba 48L1863

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info