Bedienungsanleitung Toshiba mt700 dlp projector 720p (Seite 28 von 36) (Englisch)

215054

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

Menus 28

Options menu

Use this menu to adjust the global settings for the projector.

1. Background Color: Allows you to choose the color of the background screen that will display

when there is no input signal detected.

2. OSD Off (Secs): Sets the length of time the OSD will remain active after your last button press.

The range is from 5 to 60 seconds.

3. Sleep Timer (Min): Sets the auto-shutdown timer. The timer can be set to a value between 10

minutes and 3 hours.

4. OSD Position H: Adjusts the horizontal position of the OSD.

5. OSD Position V: Adjusts the vertical position of the OSD.

6. Reset Settings: Returns all settings to the factory preset values.

Setup menu

Use this menu to adjust basic image setup functions.

1. Language: Sets the language for the OSD menus. There are seven languages available,

English, French, Spanish, German, Italian, Japanese, and Portuguese.

2. Projection Mode: The projector can be installed on a ceiling or behind a screen, or with one or

more mirrors. You can choose from four settings. Contact your dealer for the ceiling mounting

bracket if you need to install the projector on a ceiling.

3. Keystone: Corrects for trapezoidal distortion resulting from the angle of projection. It can provide

correction of up to ± 12 degrees.

4. Altitude: Set the Altitude to High when you use the projector in an area higher than 3000 feet in

altitude or when the ambient temperature is higher than 40°C (100°F).

Note: Operating the projector in "High" mode may cause louder fan noise because of increased

fan speed necessary to improve overall cooling system and performance.

If the projector is used in any extreme environment (including those listed above), the projector

may begin auto shut-down to prevent overheating. If this happens, try setting the Altitude feature

to High. If this does not solve the problem, shut down the projector.

Note: This projector was not designed to operate in all harsh or extreme environments.

5. Video Mode: When you set the Video Mode to Auto, the projector will automatically identify the

input signal type. If it fails, set the Video Mode to Manual and select a system from the list.

6. NTSC Mode: If your residential area is using the NTSC system, set the your location as Japan or

US.

7. Test Pattern: Use the Display menu Test Pattern feature when installing the projector without

an input signal, to help you adjust the image size and focus. The test pattern will display in the

aspect ratio setting of the Screen Size.

8. Lamp

Q Lamp Power: Select High lamp power to project brighter images.

Using the High lamp power setting will decrease the life of the lamp faster than using the Standard

setting.

Q Lamp Time: Displays [Lamp Time] as a measure of when the lamp time should be replaced.

(Cannot be used as a counter of guaranteed lamp time.) When the displayed time approaches

2,000 hours, consult with a store about getting TLPLMT70 replacement lamp (sold separately)

prepared.

Q Reset Lamp Timer: Resets the lamp timer. This should only be done after the lamp has been

replaced.

p. 15

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Toshiba mt700 dlp projector 720p Seite 28

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info