497513
6
Zoom out
Zoom in
Vorherige Seite
1/21
Nächste Seite
5
EN
Setting the current day of the week and clock time
Set the current clock time and day of the week.
The day of the week and clock settings can be
performed whether the air conditioner is running or
shut down.
* The air conditioner continues to operate (run) while
the day of the week and clock settings are being
performed.
The normal operation of the air conditioner or a
program for a scheduled operation can be input even
without performing the day of the week and clock
settings, but the scheduled operation cannot be
executed. In order to execute scheduled operations,
the day of the week and clock must be set without fail.
Before this remote controller is shipped from the
factory, the initial setting (default) of the 24-hour
display is established for the clock time display, but
this can be changed to the 12-hour (AM/PM) display.
* If you want to use the 12-hour time display, refer to
the “Selecting the remote controller functions”
section.
* In these instructions, the 24-hour display is used in
the figure and descriptions.
Preparations
Turn on the ground fault interrupter.
When the power is turned on, a dividing line appears
on the remote controller display.
* For about a minute after the power has been turned
on, on the LCD screen blinks, and there
will be no response to the keys of the remote
controller even when they are pushed.
1 Hold down the button (48)
for at least 4 seconds.
The display transfers to the day
of the week/clock setting screen.
The whole LCD display blinks.
2 Repeatedly push the button
(45), and select the current day of the week.
Move the day arrow to the position above the
current day of the week.
The LCD display continues to blink.
3 Push the TIME and buttons (40), and
select the current clock time.
Each time the button (40) is pushed, the clock
is moved forward by one minute.
Each time the button (40) is pushed, the clock
is moved back by one minute.
When the or button is held down, the clock
is moved forward or back in 10-minute increments.
The LCD display continues to blink.
4 Push the button (42) to return to the original
screen.
As soon as the button is pushed, the clock starts
running. (Do this in synchronization with a time
signal.)
on the LCD screen goes off.
After the clock has been set, the entire LCD screen
lights, but the colon (“ ”) continues to blink.
<Blinks>
6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln
1

Forum

toshiba-rbc-ams41e-remote-control

Suche zurücksetzen

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Toshiba RBC-AMS41E Remote control wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info