Bedienungsanleitung Toshiba tlp wx2200 (Seite 22 von 29) (Englisch)

214861

Zoom out

Zoom in

Vorherige Seite

1/29

Nächste Seite

Operations

Using the menus (Continued)

[Key lock]

Protect from operating errors by locking on the control panel buttons of the

projector. (The remote control operations are available.)

Control panel operations are locked after the setting is done, and accordingly

operation with the control panel buttons is disabled.

•To release the key lock, set the [Key Lock] to [Off] using remote control. Pressing

the [RETURN] button on the projector for 10 seconds also sets the [Key Lock] to

[Off]. (When operating the main unit, the 2 indicators of LAMP and TEMP light in

orange for 3 seconds, and at the same time the projector beeps.)

■ Displaying Information (Status display)

This displays information about the input signal, lamp use time, etc.

“Yes”: displayed, “No”: not displayed

Item Description

Computer Y/PB/PR Video S-video

Projector

Input Input source name Yes Yes Yes Yes

Mode name RGB input mode

[Note 1]

Ye s N o N o N o

Resolution Resolution (in dots) Yes No No No

Frequency Sync frequency Yes No No No

Sync Sync signal polarity

[Note 2]

Ye s N o N o N o

Signal format Y/P

signal format No Yes No No

Video mode Color method of video signal No No Yes Yes

Lamp time Time of lamp use

[Note 3]

Ye s Ye s Ye s Ye s

Lamp reset count The count for lamp replacement Yes Yes Yes Yes

Total time The total time that this projector is used. Yes Yes Yes Yes

Version Firmware version

[Note 4]

Ye s Ye s Ye s Ye s

Notes

1: The mode of supported RGB signals

p.52

is shown.

2: Sync signal polarity shown as P (positive) or N (negative) for [H/V].

3: Displays [Lamp time] as a measure of when the lamp should be replaced. (Cannot be used as

a counter of guaranteed lamp time.) Please replace the lamp after 2000 hours of use if [Lamp

power] is set to [Standard], or after 3000 hours of use if [Lamp power] is set to [Low], consult

with a dealer about getting replacement for lamp TLPLW11 (sold separately).

4: [Version] shows the version of the projector’s internal control program. This version is referred

to for customer service, etc.

Note

• The displayed information will not be refreshed if the status changes. To refresh the

information, dismiss the display, then display it again.

Default setting 2 menu

DescriptionItem

Sets projection mode in accordance with Placement Style.

Sets the cooling fan speed.

When two or more projectors are used and controlled by the remote

control respectively, this menu sets the code for the projector and the

remote control.

[ or : Enter setting mode] [ : Select from 1, 2, 3, 4]

[ :Confirm] [ :Select OK to end]

Press [Cancel] to return.

Lock the control panel buttons.

[ or : Enter setting mode] [ : Select On/Off]

[ :Confirm] [ :Select OK to end]

Press [Cancel] to return.

Press . (The password and user logo are not reset.)

Resets all adjustments and settings to their factory settings.

Password setting

Projection

mode

Fan mode

Remote

control

Key lock

Reset all

Password

Yes No

Standard High

(Rear

ceiling)

(Standard)

(Rear) (Ceiling)

p.21

p.32

Detailed description

[Fan mode]

Setting [Fan mode] to [High] increases the cooling fan speed. (The cooling fan

noise gets louder.) Set this option to use the projector, for example, at high altitude

(over 1,500 meters above sea level).

• Do not set Fan mode to [High] when using the projector at a lower altitude.

[Remote control]

Sets a remote control code from 4 types. You can set each code respectively for up

to 4 projectors. The factory setting is [1].

To switch codes, set the same code for the projector and the remote control.

A remote control code is applied after the setting is done.

•You cannot operate the remote control if the codes of the projector and the

remote control do not match.

Remote control code setting for remote control

Remove the battery cover and set the same remote control code switch as the

projector.

p.16

p.17

(Use a screwdriver with thin tip to set.)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Toshiba tlp wx2200 Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info