Bedienungsanleitung Trek 1997 sensor (Seite 3 von 6) (Englisch)

775412

Zoom out

Zoom in

Vorherige Seite

1/6

Nächste Seite

The Trek Sensor Computer attaches to

the mounting bracket by sliding the unit

onto the bracket from the back until it

snaps firmly into position. To remove the

computer from the bracket, place your

thumb against the back of the mounting

bracket and pull the computer toward you

with your index finger.

Maximum Speed (MXS)

The Maximum Speed reached during a ride is

displayed in 0.1 mi/Km increments on the

top line, with the MXS icon. Maximum

Speed is stored in

memory and is updated each time a new,

higher speed is reached.

CLOCK (CLK)

The 12 hour clock is displayed on the lower

line, indicated by the CLK icon.

ATM “Lap Timer” Display

A unique ATM “Lap Timer” display allows

you to lock the display at the end of a ride

segment and view the ATM, DST, AVS

and MXS at a later time.

This is especially useful at the end of a race,

allowing you time to cool down without

adding time to your Stopwatch.

As you cross the finish line, press the left

key for over 1 second to freeze information

on the display. You may continue to ride,

viewing the information locked on the flash-

ing locked display. The computer will con-

tinue to record information and store it in

memory. Press the left key to update the

current display information.

RESETTING THE COMPUTER

In SPD/ATM mode, press both keys for over

two seconds to clear ATM, DST, AVS and

MXS display.

SLEEP MODE

To conserve battery power, the computer

will enter the ‘Sleep’ mode after 5 minutes

of no speed input, blanking the display.

Press any key to enter normal operating

modes.

(Note: Unit will not enter sleep mode in

setting function mode.)

1. Position the sensor unit to the inside of

either the right of left fork blade

anywhere from 3-6 inches up from the fork

blade tip. Attach the sensor to the fork

blade with the quick ties but do not tighten

the ties completely until final adjustment is

complete.

INSTALLATION

Sensor and Wheel Magnet

2. Attach the wheel magnet to a spoke,

aligning the magnet with the sensor so it

faces and intersects the bottom polished

line on the sensor. The magnet should have

1-2 mm clearance from the sensor. If the

sensor and magnet are too close or touch-

ing, rotate the sensor unit toward the back

of the fork blade until adequate clearance is

achieved. Carefully tighten the quick ties

making sure you maintain the proper space

between the magnet and the sensor. Trim

the excess quick tie strap using a scissors

or fingernail clipper. Tighten the magnet

screw, but be careful not to over tighten as

this can damage the fitting.

Sensor Wiring and Bracket

1. Route the sensor wire up the back of the

fork blade or wind the wire around the

blade, making sure that the wire is not

loose and that you leave enough wire to

reach the handlebar. Secure the wire to the

fork blade immediately above the sensor

and at the top of the fork blade, using the

adhesive strips

that are provided or electrical tape.

2. Wind the wire upward around the front

brake cable until the wire is adjacent to the

handlebar, allowing enough slack for free

movement of the steering assembly cables.

3. Attach the bracket to the handlebar on

either side of the stem. The bracket goes

onto the handlebar with the wire toward the

rider side of the bar. Use the appropriate

rubber shim between the bracket and han-

dlebar to provide a secure fit.

Shims will

prevent slipping

Attaching the Computer to

the Bracket

Sensor 1.0 97 6/12/00 11:17 AM Page 6

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Trek 1997 sensor Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info