Bedienungsanleitung Trek 1997 sensor (Seite 4 von 6) (Englisch)

775412

Zoom out

Zoom in

Vorherige Seite

1/6

Nächste Seite

1. Remove the battery cover from the back

side of the computer using a

narrow flat blade screwdriver.

2. Install the battery so that the

positive "+" side of the battery is visible,

and replace the battery cover.

CAUTION: On the bottom of the computer

head next to the battery door is a small

recessed button. This is the Auto Clear

Button. Pressing this button will clear all

memories and reset all functions to their

default values.

All Clear Button

COMPUTER SET UP

Battery Installation

BUTTON FUNCTIONS

PROGRAMMING YOUR TREK

SENSOR CYCLE COMPUTER

Setting the Clock

1. Press the mode key to advance

to MXS/Clock display.

2. Press and hold the mode key for over 2

seconds until hours setting

begins to flash.

3. Press the adjust key to adjust hours

setting, press the mode key to confirm and

advance to minutes setting.

4. Press the adjust key (hold for fast

advance) to adjust the minutes, and press

the mode key to confirm setting and enter

normal display mode.

Mode Button

Adjust

Button

Setting Miles/ Kilometers and

Wheel Size

1. Press mode computer key to enter

AVS/ODO mode.

2. Press and hold mode key for over 2 sec-

onds until m/h begins to flash.

3. Press adjust key to select miles (m/h) or

kilometers (km/h) display.

4. Press mode key to confirm choice and

advance to wheel size setting.

5. Adjust the flashing digit with the adjust

button, confirm choice by pressing mode

button, and advance to next flashing digit.

6. Adjust and/or confirm all flashing

digits.

Wheel Size Setting

The wheel size setting number is equal to

the distance, in millimeters, that your front

wheel travels during one complete revolu-

tion. Each time the wheel magnet passes

the sensor unit on your fork, the sensor

sends an impulse to the computer telling it

that your wheel has completed one revolu-

tion. The computer calculates this distance

vs. time to give you accurate readings for

the various modes.

Determining Wheel Size Setting

There are three methods for determining the

wheel size setting. For the most accurate

computer readings, it is best to measure the

actual distance that your wheel travels in

one complete revolution. This method is

called a wheel roll out.

The Sensor is equipped with 2 buttons that

control the function of the unit.

1. MODE

Changes the Main Screens of the Sensor

2. ADJUST

Adjusts digits while programming and

activates ATM lap timer.

• Perform the wheel roll out on a hard,

flat, smooth surface such as a garage or

basement floor.

• Make sure your tires are properly inflat-

ed.

1. Position your bike so that the valve stem

of the front wheel is at its bottom most

position. Mark the spot on the floor directly

under the center of the valve stem using a

piece of tape or chalk.

2. Roll the bicycle forward in a straight line,

while putting downward pressure on the han-

dlebars to simulate rider weight. When the

wheel has completed one revolution and the

valve stem is at its bottom position, mark the

floor directly under the center of the valve

stem with tape or chalk. Measure the distance

between the two marks in millimeters. (Note:

Conversion of in. to mm. is 1 in.=25.4 mm.)

This is your wheel setting number. You can

repeat this procedure and average your results.

We recommend that you record your wheel set-

ting numbers here for future reference.

Method One: Wheel Roll Out

Sensor 1.0 97 6/12/00 11:17 AM Page 8

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Trek 1997 sensor Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info