Bedienungsanleitung Trek eBike Systems 2023 - Bosch (Seite 326 von 376) (Deutsch, Englisch, Holländisch, Französisch)

817492

326

Zoom out

Zoom in

Vorherige Seite

1/376

Nächste Seite

English – 4

Inserting and removing the rack-mounted battery (see

figureB)

In order for the battery to be inserted, the key (5) must be

inserted into the lock (6) and the lock must be open.

To insert the rack-mounted battery (2), slide it contacts-

first into the holder (1) on the rack until you hear it click into

place.

Always secure the battery by closing the lock (6) – other-

wise the lock may open and the battery may fall out of the

holder.

Always remove the key (5) from the lock (6) after closing it.

This prevents both the key from falling out and the eBike bat-

tery from being removed by unauthorised third parties when

the eBike is not in use.

To remove the rack-mounted battery (2), switch it off and

open the lock using the key (5). Pull the battery out of the

holder (1).

Removing the PowerTube battery (pivot) (seefigureC)

❶To remove the PowerTube battery(15), open the bat-

tery lock(6) using the key(5). The battery will be un-

locked and fall into the safety restraint(14).

Note: When removing the eBike battery, hold it firmly in your

hand.

❷Hold the battery firmly and press on the safety re-

straint(14) from above. The battery will be unlocked

completely and fall into your hand. Then pull the bat-

tery out of the frame.

Note: As a result of varying designs, the battery may need

to be inserted and removed using a different method. Read

the operating instructions of the eBike manufacturer.

Inserting the PowerTube battery (pivot) (seefigureD)

In order for the battery to be inserted, the key(5) must be

inserted into the battery lock(6) and the battery lock must

be open.

❶To insert the PowerTube battery (15), place it so that

its contacts are in the lower holder of the frame.

❷Twist the battery upwards until it is held by the safety

restraint (14).

❸Hold the battery lock open with the key and press the

battery upwards until you hear it click into place.

❹Always secure the battery by closing the battery

lock(6) – otherwise the battery lock may open and the

battery may fall out of the holder.

Always remove the key(5) from the battery lock(6) after

locking it. This prevents both the key from falling out and the

eBike battery from being removed by unauthorised third

parties when the eBike is not in use.

Operation

Start-up

uUse only original Bosch eBike batteries that the manu-

facturer has approved for your eBike. Using other

eBike batteries can lead to injuries and pose a fire hazard.

Bosch accepts no liability or warranty claims if other

eBike batteries are used.

Switching on/off

Switching on the eBike battery is one way to switch on the

eBike. Read and follow the instructions in the operating

manuals for the drive unit and on-board computer.

Before switching on the eBike battery, i.e. the eBike, make

sure that the battery lock(6) is locked.

To switch on the eBike battery, press the on/off button(4).

Do not use any sharp or pointed objects to press the button.

The LEDs on the indicator (3) will light up, indicating the bat-

tery's state of charge at the same time.

Note: If the eBike battery capacity is less than 5%, none of

the LEDs on the battery charge indicator(3) will light up.

Whether the eBike is switched on can only be determined

from the on-board computer/control unit.

To switch off the eBike battery, press the on/off button(4)

again. The LEDs on the indicator (3) will go out. This will also

switch the eBike off.

If no power is drawn from the drive for about10minutes

(e.g. because the eBike is not moving) and no button is

pressed on the on-board computer or the operating unit of

the eBike, the eBike will switch off automatically.

The eBike battery is protected against deep discharge, over-

loading, overheating and short-circuiting by the "Electronic

Cell Protection (ECP)". In the event of danger, a protective

circuit switches the eBike battery off automatically.

If a fault is detected in the

eBike battery, two of the

LEDs on the battery charge

indicator (3) will flash. Con-

tact an authorised bicycle

dealer if this happens.

Recommendations for Optimal Handling of the

eBike Battery

The service life of the eBike battery can be extended if it is

looked after well and especially if it is stored at the correct

temperature.

As it ages, however, the capacity of the eBike battery will di-

minish, even with good care.

A significantly reduced operating time after charging indic-

ates that the eBike battery has deteriorated. The eBike bat-

tery should be replaced.

Recharging the eBike Battery Before and During Storage

When you are not going to use the eBike battery for an exten-

ded period (longer than three months), store it at a state of

charge of around 30% to 60% (when two to three of the

LEDs on the battery charge indicator(3) are lit).

Check the state of charge after six months. If only one of the

LEDs on the battery charge indicator(3) is lit, charge the

eBike battery back up to around 30% to 60%.

Note: If the eBike battery is stored with no charge for an ex-

tended period of time, it may become damaged despite the

0 275 007 XPX | (22.02.2023) Bosch eBike Systems

326

Trek eBike Systems 2023 - Bosch Seite 326

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info