Bedienungsanleitung Trendnet TEW-716BRG (Seite 21 von 43) (Englisch)

541686

Zoom out

Zoom in

Vorherige Seite

1/43

Nächste Seite

TRENDnet User’s Guide

TEW-716BRG

Change your router IP address

Basic Setting > Network Setup

In most cases, you do not need to change your router IP address settings. Typically, the

router IP address settings only needs to be changed, if you plan to use another router in

your network with the same IP address settings, if you are connecting your router to an

existing network that is already using the IP address settings your router is using, or if

you are experiencing problems establishing VPN connections to your office network

through your router.

Note: If you are not encountering any issues or are not faced with one of the cases

described above or similar, it is recommended to keep your router IP address

settings as default.

Default Router IP Address: 192.168.10.1

Default Router Network: 192.168.10.0 / 255.255.255.0

1. Log into your router management page (see “

Access your router management page”

on page 18).

2. Click on Basic Setting and click on Network Setup.

3. Enter the router IP address settings and click Save to apply the settings.

• IP Address – Enter the new router IP address.

(e.g. 192.168.200.1)

• Subnet Mask – Enter the new router subnet mask.

(e.g. 255.255.255.0)

Note: The DHCP address range will change automatically to your new router IP

address settings so you do not have to change the DHCP address range manually to

match your new router IP address settings. You will need to access your router

management page using your new router IP address to access the router

management page. (e.g. Instead of using the default

http://192.168.10.1 using your

new router IP address will use the following format using your new router IP address

http://(new.router.ipaddress.here)

to access your router management page.

Set up the DHCP server on your router

Basic Setting > DHCP Server

Your router can be used as a DHCP (Dynamic Host Configuration Protocol) server to

automatically assign an IP address to each computer or device on your network. The

DHCP server is enabled by default on your router. If you already have a DHCP server on

your network, or if you do not want to use your router as a DHCP server, you can disable

this setting. It is recommended to leave this setting enabled.

1. Log into your router management page (see “Access your router management page”

on page 18).

2. Click on Basic Setting and click on DHCP Server.

3. Review the DHCP Server settings.

• DHCP Server – Enable or Disable the DHCP server.

• IP Pool Starting address: Changes the starting address for the DHCP server range.

(e.g. 192.168.10.20)

• IP Pool Ending Address: Changes the last address for the DHCP server range. (e.g.

192.168.10.30)

Note: The Start IP and End IP specify the range of IP addresses to automatically

asign to computers or devices on your network.

• Lease Time – Click the drop-down list to select the lease time.

Note: The DHCP lease time is the amount of time a computer or device can keep

an IP address assigned by the DHCP server. When the lease time expires, the

computer or device will renew the IP address lease with the DHCP server,

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Trendnet TEW-716BRG Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Trendnet TEW-716BRG

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info