Bedienungsanleitung Trendnet TEW-716BRG (Seite 36 von 43) (Englisch)

541686

Zoom out

Zoom in

Vorherige Seite

1/43

Nächste Seite

TRENDnet User’s Guide

TEW-716BRG

Note: Configuring this feature assumes that you have some general networking

knowledge.

1. Log into your router management page (see “

Access your router management page”

on page 18).

2. Click on Configuration at the top of the page, click on Advanced Setting, and click on

Routing.

3. Next to Static Routing, check the Enable option to enable static routing.

4. Review the static route settings.

• Destination – Enter the IP network address of the destination network for the

route.

(e.g. 192.168.20.0)

• Subnet Mask – Enter the subnet mask of the destination network for the route.

(e.g. 255.255.255.0)

• Gateway – Enter the gateway to the destination network for the route.

(e.g. 192.168.10.2)

• Hop – Enter the number of hops (routers) required to reach the destination

network. The hop count range that can be specified is 0-99.

• Enable – Check the option to enable the route and uncheck the option to disable

the route.

5. To save changes, click Save at the bottom of the page.

Note: If you would like to discard the changes, click Undo before you click Save.

Enable dynamic routing on your router

Advanced Setting > Routing

You may want set up your router to route computers or devices on your network to

other local networks through other routers. If other routers support dynamic routing

such as RIP (Routing Information Protocol), you can enable this feature on your router

to automatically learn the required routes to reach those networks. It is required that

the same dynamic routing protocol and version is also enabled on the other routers in

order your router and the other routers to exchange information about the network.

Note: Configuring this feature assumes that you have some general networking

knowledge.

1. Log into your router management page (see “

Access your router management page”

on page 18).

2. Click on Configuration at the top of the page, click on Advanced Setting, and click on

Routing.

3. Select the appropriate dynamic routing protocol and version communicate with other

routers.

• Disabled – Disable sending and receiving or exchange of routing information

dynamically between your router and other routers.

• RIPv1 - Enables sending and receiving or exchange of routing information

dynamically between your router and other routers to build routes to your network

and other networks using the RIP version 1 protocol.

• RIPv2 – Enables sending and receiving routing information dynamically between

your router and other routers to build routes to your network and other networks

using the RIP version 2 protocol.

4. To save changes, click Save at the bottom of the page.

Note: If you would like to discard the changes, click Undo before you click Save.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Trendnet TEW-716BRG Seite 36

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Trendnet TEW-716BRG

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info