Bedienungsanleitung Trendnet TEW-752DRU (Seite 24 von 58) (Englisch)

541579

Zoom out

Zoom in

Vorherige Seite

1/58

Nächste Seite

TRENDnet User’s Guide

TEW-752DRU

Firewall Rules

Access > Firewall & DMZ

You may want specify inbound or outbound access control to allow/deny sources (or

Internet IP addresses) to your network from the Internet or from computers or devices

on your network to the Internet. Firewall rules may allow for more granular control of

specific inbound and outbound access between your network and the Internet. It is

recommended that these settings remain set to default unless you are knowledgeable

about the effects of changing the firewall rule configuration. It is possible to have

undesirable functionality from your router if these settings are improperly modified. You

can enter up to 32 firewall rule entries.

1. Log into your router management page (see “Access your router management page

”

on page 25).

2. Click on Access, click on Firewall & DMZ.

3. Review the settings under Firewall Rules section. Click Save Settings to save settings.

Check the box next to the firewall rule entry to enable it. Uncheck the option to disable

the firewall rule entry.

• Name: Enter a name for the firewall rule.

• Action: Select Allow will allow access and selecting Deny will block or deny access.

• Interface (Source): Click the drop-down list and select LAN (from your network) or

WAN (from the Internet) depending on where the traffic will be coming from.

• IP Address (Source): Enter the IP address or IP address range to apply the protocol

(e.g. 192.168.1.20-192.168.1.20 or 192.168.1.20-192.168.1.30). To specify all IP

address, enter an asterisk * .

Note: The filter will not be applied to IP addresses outside of the range specified.

• Interface (Destination): Click the drop-down list and select LAN (your network) or

WAN (Internet) depending on where the traffic will be coming from.

• IP Address (Destination): Enter the IP address or IP address range to apply the

protocol (e.g. 192.168.10.20-192.168.10.20 or 192.168.10.20-192.168.10.30). To

specify all IP address, enter an asterisk * .

• Protocol: Select the protocol type to filter. TCP, UDP, ICMP, or All.

• Port Range: If selecting TCP or UDP protocol, enter the port number or range of

port numbers to apply in the firewall rule. (e.g. 80-80 or 20-21). For all ports, use

the port range 1 - 65535.

• New Schedule: Click the drop-down list to select the pre-defined schedule to apply.

The filter will only be active during the time period defined in the pre-defined

schedule. (See “Create Schedule

” section on page 34).

Note: Before applying scheduling, please ensure your Time settings are configured

correct and you have defined a schedule. See page 34 to configure Time Settings

and see

page 34 to Create Schedule.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Trendnet TEW-752DRU Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Trendnet TEW-752DRU

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info