7
GB
Battery charging table
Red LED Green LED
Charger plugged In OFF Flashing
Charger evaluating battery OFF Flashing
Fast charging ON OFF
Highly discharged battery slow charging Flashing OFF
Abnormal battery temperature charging Flashing OFF
Fully Charged OFF ON
Battery or charger fault Flashing Flashing
T ON ON
Note: If the lights on the Battery Charger (11) fail to illuminate according to the chart above or
indicate a fault condition:
• Check the battery is firmly seated in the Batter
• Check all connections and that mains power is switched on
Initial charge
• The initial charge will vary depending on the existing charge in the battery.
battery to reach full charge as indicated on the Batter
• After discharging, recharge the battery completely
charger
highest capacity
• Subsequent full charges will take approximately 80 minutes (T20HCB: 4Ah battery).
However
Re-charging the battery
• After use, a lithium-ion battery must be allowed to cool down before charging
• If a hot battery is inserted into the charger both LEDs will illuminate. The charger will
begin to charge when the Battery has cooled sufficiently (this may take several minutes)
Battery - length of ser
• The length of service from each charging cycle will depend on the type of workload.
battery charger and batter
working life.
the ideal charging rate for the condition of the battery.
charging or charging at too high a rate. However
reduced over time
T
• Store and charge the battery in a cool area. T
temperature will reduce battery life
• Never store lithium-ion batteries in a discharged condition. Recharge them immediately
after they are discharged. F
charged
• All batteries gradually lose their charge, even lithium-ion batteries,
is very low. If the drill is stored for long periods of time without use,
every three to four months and disconnect the battery from the po
stored.
Fitting a drill or driver bit
WARNING:
of the machine.
1. Rotate the Keyless Chuck (1) collar clockwise and insert the bit into the chuck
2. Rotate the Keyless Chuck collar anti-clockwise to secure the drill bit
Note: DO NOT run the tool whilst tightening or releasing the chuck.
middle position of the Forward/Reverse Switch (5).
3. When the bit is held tightly
should rotate smoothly without uneven rotation. If the bit is not central,
reposition the bit and retighten the chuck
Direction control
• The rotation direction can be set using the Forward/Reverse Switch (5)
• T
• T
• When the Forward/Reverse Switch is in the central position,
WARNING:
Speed control
• This drill driver features a 2-speed gearbox:
- 1st gear range: 0 – 450min-1
- 2nd gear range: 0 – 1600min-1
• Use the Gear Selector (4) to set the gear: forward for first gear
Note:
torque and superior control at low rpm.
for drilling.
T
• This drill driver is fitted with torque control, which limits the torque output of the drill,
enabling screws to be driven without the risk of damage
• There are 16 torque settings and two drill settings.
torque
• T
the setting you require is aligned with the arrow on the combi hammer drill housing
• Check that the torque setting is correct by practising first on a piece of scrap material
Mode selection
• For drilling, .
This will lock the tool for maximum torque
• For screwdriving,
symbol .
• For masonry drilling, select the correct gear
symbol .
function
WARNING:
not attempt to use this tool in the drill position when doing so. Use the 16 torque settings and
the first gear to allow the torque clutch to protect the tool from excessive load.
spanner to loosen or tighten a nut/bolt is recommended.
operation, without risk of damage when high torque is required at the beginning or end of
the operation.
Operation
WARNING :
respiratory and hearing protection, when working with this tool.
Switching on and off
• T
will illuminate
• Further pressure on the Speed Control T
the tool
• Release the Speed Control T
Note: It is possible the drill may switch off during heavy use due to thermal protection of the
battery and internal components. This may prevent the tool being used again for a short period
of time and does not represent a fault condition.
Drilling guidance
• Use sharp drill bits and ensure that drill bits are suitable for the material being drilled
• Never exceed the maximum drilling capacities listed in ‘Specification’
• Begin drilling at slow speeds by partially squeezing the Speed Control T
• Reduce pressure on the Speed Control T
through to the other side of material
• T
of the workpiece or continue the hole from the back of the wood when the drill bit first
breaks through
Drilling metal
• Support thin material with a piece of scrap wood
• Mark the intended hole position using a hammer and centre punch
• Use only HSS (high speed steel) drill bits or others recommended for drilling into metal
• Prior to drilling large holes, use a smaller bit to drill a pilot hole
• Use a suitable coolant/lubricant to prolong the service life of the drill bit, and produce good
results
Drilling masonry
• Always use a masonry drill bit, preferably a TCT masonry bit,
stone or concrete
• DO NOT apply too much pressure to the back of the tool. If debris blocks the drill hole,
the drill slowly and remove the bit from the hole. Repeat until the hole is clear of debris
and continue
100901_Z1MANPRO1.indd 7 11/07/2016 14:39
