Bedienungsanleitung Triton T20CH (Seite 8 von 40) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

665033

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

Troubleshooting

Problem Possible cause Solution

Red charging LED does not illuminate and battery

not charging

Battery not fully seated Clean battery socket of charger

Charger not powered Recheck mains connection

Battery pack has low capacity

Battery not being fully charged Charge the battery until the charger indicates a

full charge

Battery pack has been charged over 100 times

and capacity has started to reduce

This is normal for batteries. Contact your Triton

dealer to purchase a replacement battery

Drill cannot be switched on (trigger switch does

not move)

The forward/reverse switch may be in the middle

(‘locked’) position

Slide the forward/reverse switch either to the

left or right

Drill does not start when on/off trigger switch is

depressed

Battery completely discharged Recharge battery or replace with a fully

charged battery

Defective battery Replace battery

Machine defective Contact your Triton dealer or authorised

service centre

Screws do not reach deep enough into the

workpiece

Not enough torque; torque clutch setting too low Choose a higher torque setting

Low battery voltage Recharge battery or replace with a fully

charged battery

Screws are driven too deep into the workpiece

surface

Too much torque; torque clutch setting too high Choose a lower torque setting

During masonry drilling the drill bit does not

penetrate the wall

Unsuitable or blunt drill bit Replace drill bit with a new high quality masonry

drill bit

Drill bit too large See ‘Speciﬁcations’ for maximum

drilling capacities

Drill not set to hammer mode Rotate mode selector to switch the machine into

hammer drill mode (see ‘Mode Selection’)

Accessories

• A range of accessories, including a 2Ah battery (T20B), 4Ah high capacity battery

(T20HCB), drill and screwdriver bits is available from your Triton dealer. Spare parts can be

purchased from your Triton dealer or online at www.toolsparesonline.com

Maintenance

• This tool is manufactured using class-leading components and makes use of the latest

in intelligent circuitry that protects the tool and its components. In normal use it should

provide a long working life

Cleaning

• Keep your machine clean at all times. Dirt and dust will cause internal parts to wear

quickly, and shorten the machine’s service life. Clean the body of your machine with a

soft brush or dry cloth. If available, use clean, dry, compressed air to blow through the

ventilation holes

Storage

• Store this tool and its accessories after use in its case, in a dry, secure place out of the

reach of children

Disposal

Always adhere to national regulations when disposing of power tools that are no longer

functional and are not viable for repair.

• Do not dispose of power tools, batteries or other waste electrical and electronic equipment

(WEEE), with household waste

• Contact your local waste disposal authority for information on the correct way to dispose

of power tools and batteries

100901_Z1MANPRO1.indd 8 11/07/2016 14:39

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Triton T20CH Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info