6
GB
g) Make sure there are no nails or other foreign objects in the area of the workpiece to
be sanded.
h) Never use this sander for wet sanding. Failure to comply may result in electrical shock,
causing serious injury or worse.
i) Use only identical replacement parts when servicing this spindle sander
j) Make sure the spindle has come to a complete stop before touching the workpiece.
k) TSanding lead-based paint is NOT
RECOMMENDED.
poisoning.
When sanding paint:
a) Protect your lungs. W
b) Do not allow children or pregnant women in the work area until the paint sanding
job is finished and the clean-up is completed
c) Do not eat, drink,
d) Use a dust collection system when possible. Seal the work area with plastic.
track paint dust outside of the work area
e) Thoroughly clean the area when the paint sanding project is completed
Product Familiarisation
1. On-Board T
2. On/Off Switch
3. Motor Housing
4. Table T
5. Spindle
6. Spindle Lock Nut
7. Lower
8. On-Board Spindle Storage
9. Upper Spindle Washers (x3)
10. Table Insert (x 6)
11. Sanding Sleeve (x 6)
12. Rubber Drum (x 5)
13. Dust Extraction Port
14. Wrench
Intended Use
Bench-mounted sanding machine with a rotating and height oscillating sanding drum.
For sanding curved and straight surfaces on intricate as well as larger workpieces.
Unpacking Y
• Carefully unpack and inspect your tool. Fully familiarise yourself with all its features and
functions
• Ensure that all parts of the tool are present and in good condition. If any parts are missing
or damaged, have such parts replaced before attempting to use this tool
Before Use
WARNING: Ensure the tool is disconnected from the power supply before attaching or
changing any accessories, or making any adjustments.
Bench mounting
If the spindle sander is to be used in a permanent position, it is recommended that you secure
it to a rigid work surface.
• Use the holes in the base of the spindle sander (image A) as a template to mark and drill
four holes in your intended mounting surface (ie workbench). Secure the spindle sander
into position using large bolts, washers and nuts (not supplied)
• If the spindle sander is intended to be more portable, fix a board to the base which can be
easily clamped and removed from various mounting surfaces
• f using bolts make sure they are long enough to penetrate the workbench or board
sufficiently for a secure fix
Note: Use nylon insert lock nuts or spring washers in the fixings to prevent vibration from
loosening the fixings.
Note: Never use bolts that require force to push through the Bench Mounting Holes as these
may crack the plastic body as will over-tightening the fixings.
Dust extraction
It is recommended that the spindle sander is used with a dust extraction system for a cleaner
and safer work environment.
1. Attach the hose from the dust extraction system to the Dust Extraction Port (13) and
ensure it is secure
2. For greatest efficiency,
sander
Selecting a table insert
Failure to use the correct table insert with its matching sanding sleeve could result in pinched
fingers or the workpiece being pulled down between the table insert and the sanding sleeve.
The sanding sleeve should fit snugly into the central cutout of the table insert (Images B
and C).
Use the following chart to help determine the correct table insert and upper spindle washer to
use with each sanding sleeve.
Sanding
Sleeve Dia
T
Insert Size
Upper Spindle
Washer Size
13 mm / 1/2" 13 mm / 1/2" Small
19 mm / 3/4" 19 mm / 3/4" Medium
26 mm / 1" 26 mm / 1" Medium
38 mm / 1 1/2" 38 mm / 1 1/2" Large
51 mm / 2" 51 mm / 2" Large
76 mm / 3" 76 mm / 3" Large
Selecting the right grade of sanding sleeve
• Sanding sleeves are available in a variety of different grades: coarse (80 grit),
(150 grit) and fine (240 grit)
• Use a coarse grit to sand down rough finishes, medium grit to smooth the work,
grit to finish off
• Always use good quality sanding sleeve to maximise the quality of the finished task
• It is advisable to do a trial run on a scrap piece of material to determine the optimum
grades of sanding sleeve for a particular job. If there are still marks on your work after
sanding, try either going back to a coarser grade and sanding the marks out before
recommencing with the original choice of grit, or try using a new piece of sanding sleeve
to eliminate the unwanted marks before going on to a finer grit and finishing the job
Fitting a sanding sleeve
Note: All of the Sanding Sleeves (11), except the smallest 13mm (1/2”) Sanding Sleeve fit over
a matching Rubber Drum (12).
Note: Ensure there is no contact between the Sanding Sleeve and the T
turning the machine on.
1.
(Image D)
2.
Drum, (except when using the 13mm sanding sleeve)
3.
table insert’
4.
Ensure the T
5.
6.
7.
•
•
•
8.
to expand the Rubber Drum against the Sanding Sleeve. Do not over
•
maximise its service life by using the remaining grit
Note: If the sleeve rotates on the drum when switched on, the Spindle Lock Nut has not been
sufficiently tightened to compress the drum and therefore grip the sleeve.
IMPORTuse a sanding sleeve that is too worn.
build-up and damage the rubber drum. Damaged rubber drums due to worn sanding sleeves
will not be covered under warranty
Operation
WARNING:
as well as suitable gloves, when working with this tool.
WARNING: ENSURE gloves and clothes worn do not have loose threads that could get
caught by the rotating spindle and drag your hand or head into the rotating spindle causing
severe injury.
Switching on and off
• The On/Off Switch (2) is located on the front of the spindle sander (Image A)
• T
• T
516693_Z1MANPRO1.indd 6 30/08/2016 16:28
