Bedienungsanleitung Triumph-Adler P-C3060DN (Seite 70 von 81) (Englisch)

651339

Zoom out

Zoom in

Vorherige Seite

1/81

Nächste Seite

Troubleshooting 4-7

Device busy

This message is displayed when Remove Device was selected while a USB memory

was being used.

The previous screen is displayed again 1 or 2 seconds.

Duplex disabled

Press GO

You attempted to print with a paper size and paper type that cannot be used for duplex

printing. Press [GO] to print onto one-side of the paper only.

Enter Account

An account code must be entered. This message is displayed if you try to print from the

operation panel (e.g. printing a status page or using the Job Retention function) when

the Job Accounting function is enabled. For more information, refer to Job Accounting

(Job Accounting selection/setting) section of the Advanced Operation Guide.

Envelope mode

Displayed when the envelope switch is set to envelope mode.

Error.Power off.

F###

Turn the power switch off and then back on again. If this message still remains, turn the

power switch off, and contact your service representative or authorized service center.

Error.Power off.

F000

The printer controller and operation panel cannot exchange data. Turn the printer off

and unplug it from the mains power supply. Then contact your service representative or

authorized service center. See the back page of this manual for the relevant phone

numbers.

Exceeded Max.output

Press GO

This message is displayed when the Job Accounting function is enabled and an

attempt has been made to exceed the print limit set for each account. To return the

printer to the print-ready status, press [GO].

For more information, refer to Job Accounting (Job Accounting selection/setting)

section of the Advanced Operation Guide.

Format SSD.

The SSD installed in the printer is not formatted, and therefore cannot be read or

written.

ID error

The user ID entered for a private job, or a stored job is not correct. Check the user ID

that you specified on the printer driver. For more information, refer to Job Box section

of the Advanced Operation Guide.

Illegal Account

Press GO

This message is displayed when the Job Accounting function is enabled and no

account is set for a transmitted print job or the specified account is not registered (the

incorrect account is set). To return the printer to the print-ready status, press [GO].

For more information, refer to Job Accounting (Job Accounting selection/setting)

section of the Advanced Operation Guide.

Job not stored

Press GO

Printing using the Job Box function failed because there was insufficient space

available on the hard disk or RAM disk, or because the RAM disk was disabled when

demounting the hard disk. To print an error report and return the printer to the print-

ready status, press [GO].

Job restricted

Press GO

This message is displayed when printing was attempted, despite the Job Account

function being on with Restriction applied as the job limit for each job account.

To return the printer to the print-ready status, press [GO].

For more information, refer to Job Accounting (Job Accounting selection/setting)

section of the Advanced Operation Guide.

Message Corrective Action

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Triumph-Adler P-C3060DN Seite 70

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Triumph-Adler P-C3060DN

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info