Bedienungsanleitung Trotec PAC2600X (Seite 14 von 21) (Englisch)

688784

Zoom out

Zoom in

Vorherige Seite

1/21

Nächste Seite

14 EN

local air conditioner PAC 2100 X / PAC 2600 X

Switching the LEDs on the control panel on or off

The control panel illumination at the devices can be switched on

and off.

This setting can only be made using the remote control.

1. Press the LED button(23).

ð The LEDs on the control panel will be switched off.

ð The device continues to run with the selected settings.

2. Press the LED button(23) again.

ð The LEDs on the control panel will be switched back on.

Saving preferred settings

You can save your preferred settings and return to the previous

setting.

This setting can only be made using the remote control.

1. Press and hold the SHORT CUT button(20) for 3s.

ð The display(19) goes blank for 1s.

ð The current settings including operating mode, target

temperature, fan stage and night mode (if activated) will

be saved.

2. Press the SHORT CUT button(20) for 1s.

ð The display(19) goes blank for 1s.

ð The device returns to the previous setting including

operating mode, target temperature, fan stage and night

mode (if activated).

3. In order to delete the settings, press the SHORT CUT

button(20) again for 3s.

ð The display(19) goes blank for 1s.

ð The settings are now deleted.

FollowMe function

Using the FollowMe function, the remote control measures the

temperature at your current location. The degree of cooling is

controlled by the air conditioner based on the measured

temperature.

The FollowMe function can be activated in cooling mode and

during automatic operation.

1. Press the FOLLOWME button(37).

ð The FOLLOWME indication(38) appears on the

display(19).

ð The remote control sends a temperature signal to the air

conditioner every 3minutes.

2. Press the FOLLOWME button(37) again to disable the

FollowMe function.

Memory function

After a power failure during operation the device will

automatically be switched back on. The chosen operating mode

settings will be saved, a possibly programmed timer will not.

All the chosen settings (incl. timer) remain saved on the remote

control. As soon as the device receives an input from the remote

control, the settings will be transmitted from the remote control

to the device.

The compressor may start up with a delay of 3min, as it is

provided with an internal protection against direct restart.

Energy saving

Upon reaching the preselected target temperature the

compressor will be switched off automatically in order to reduce

the power consumption.

Once the preselected target temperature is exceeded, the

compressor switches back on.

Automatic defrost

At low ambient temperatures, ice may form at the evaporator.

The device will then carry out an automatic defrost.

The compressor switches off and the fan keeps running until

defrosting is completed. The duration of the defrost process can

vary.

Do not switch the device off during automatic defrost. Do not

remove the mains plug from the mains socket.

Shutdown

Warning of electrical voltage

Do not touch the mains plug with wet or damp hands.

• Switch off the device.

• Hold onto the mains plug while pulling the power cable out

of the mains socket.

• Empty the condensation tray if necessary.

• If necessary, remove the condensation drain hose and any

residual fluid from it.

• Clean the device according to the Maintenance chapter.

• Store the device according to the Storage chapter.

Errors and faults

The device has been checked for proper functioning several

times during production. If malfunctions occur nonetheless,

check the device according to the following list.

The device does not start:

• Check the power connection.

• Check the power cable and mains plug for damages.

• Check the on-site fusing.

• Observe the operating temperature according to the

Technical data chapter.

• The condensation tank may be full. Empty the

condensation tank, if need be. The error codeP1 must not

be indicated on the segment display.

• Wait for 10minutes before restarting the device. If the

device is not starting, have the electrics checked by a

specialist company or by Trotec.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Trotec PAC2600X Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Trotec PAC2600X

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info