Bedienungsanleitung Trotec PAGS10-125 (Seite 14 von 20) (Englisch)

753914

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

14 EN

angle grinder PAGS 10-125

10. Check the cutting disc(14) for proper fit.

11. Check whether the cutting disc can rotate freely. Make

sure that the disc does not touch the guard or any other

parts.

12. Carry out a test run of approx.1minute without load prior

to every disc change and every start-up in order to check

the cutting disc for correct fit.

Caution

If the disc is out-of-round, rotates unevenly, vibrates,

oscillates, or if unusual noises or sparks are generated,

the cutting disc must be exchanged immediately.

Otherwise, there is a risk of injury.

Speed selection

The required speed depends on the material and the operating

conditions and can be determined by way of field-testing. It is

recommended to use a higher speed level for cutting and

grinding harder materials, and a lower speed level for softer

materials.

The setting range covers the levels 1 – 6 (3,000 – 12,000rpm).

You can change the preselected speed level at any time.

1. Turn the setting wheel(3) to the desired rated speed level.

Connecting the power cable

1. Insert the mains plug into a properly secured mains

socket.

Operation

Tips and notes on handling the angle grinder

General information:

• Carry out a test run of approx.1minute without load prior

to every disc change and every start-up in order to check

the cutting disc for correct fit.

• Only use tools which are approved for the device used.

• Before every application, make sure that you have selected

the correct tool for the intended use.

• Check the tool in the tool holder for proper fit before every

application. The tool must be firmly locked in place in the

designated holding fixtures on the tool holder.

• Check whether the cutting disc can rotate freely. Make

sure that the disc does not touch the guard or other parts.

• Only use discs with a speed imprinted that is at least as

high as the speed indicated on the device's nameplate.

• Clamp the workpiece unless it is firmly and safely

positioned by its own weight.

• Do not overload the device so that it comes to a standstill.

• After operation at high load, let the device run at idle for

several minutes to allow the tool to cool down.

• Do not touch the discs until they have cooled down.

• Keep the venting slots clear to prevent the motor from

overheating.

Cutting:

• Only use intact, flawless cutting discs. Bent, blunt or

otherwise damaged cutting discs could break.

• Never use the cutting disc for roughing!

• Only advance moderately during operation and make sure

that the cutting disc does not get jammed.

• Do not slow down the decelerating cutting disc by pressing

against the side of the disc.

• Always move the cutting disc through the workpiece in

reverse rotation.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Trotec PAGS10-125 Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Trotec PAGS10-125

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info