Bedienungsanleitung Trotec PAGS10-125 (Seite 16 von 20) (Englisch)

753914

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

16 EN

angle grinder PAGS 10-125

Errors and faults

The device has been checked for proper functioning several

times during production. If malfunctions occur nonetheless,

check the device according to the following list.

Troubleshooting tasks which require the housing to be opened

must only be carried out by an authorized specialist electrical

company or by Trotec.

The only exception is the replacement of the carbon brushes

(see chapter Replacing the carbon brushes).

Light smoke or odour is emitted during the first use:

• This is not a fault. These phenomena disappear after a

brief runtime.

The device does not start:

• Check the power connection.

• Check the power cable and mains plug for damage. If you

notice damages, do not try to take the device back into

operation.

If the supply cord is damaged, it must be replaced by the

manufacturer, its service agent or similarly qualified

persons in order to avoid a hazard.

• Check the on-site fusing.

Info

Wait for at least 10 minutes before switching the

device back on.

The cutting disc is loose:

• Check whether you are using a cutting disc that is suited

for this device.

• Make sure that the mounting flange(13) is firmly locked in

place in the designated recesses.

• Make sure that the cutting disc(14) sits flush on the

mounting flange(13) without clearance.

• Make sure that the flat side of the clamping nut(15) rests

on the cutting disc(14).

The guard is loose:

• Make sure that the coded projections(11) are firmly locked

in place in the designated groove.

• Make sure that the locking lever(12) is folded in

completely.

• If necessary, tighten the adjusting screw(10).

The cutting disc does not move although the motor is

running:

• Make sure that the clamping nut(15) is firmly tightened,

see chapter Tool change.

• Make sure that there is no workpiece debris blocking the

drive. Remove the blockages, if any.

• Make sure that the cutting disc is not jammed in the

workpiece.

The motor slows down:

• Check whether the device is overloaded by the workpiece.

• Reduce the pressure applied on the workpiece.

• Check whether the workpiece is suitable for the tasks to

be carried out.

• Check whether the carbon brushes(20) are worn out. If

necessary, replace them; see chapter Changing the carbon

brushes.

The cutting disc experiences difficulties penetrating the

material to be processed or the cutting performance is

insufficient:

• Check whether the chosen cutting disc is suitable for the

material to be processed.

• If the cutting disc is worn, replace it with a new one.

• Check the set speed; it must be suitable for both the tool

and the material.

• To select a higher speed, turn the setting wheel for speed

selection(3) to the right.

The device becomes hot:

• Check whether the cutting disc is suitable for the tasks to

be carried out.

• Make sure not to exert too much pressure on the device

during operation.

• To select a lower speed, turn the setting wheel for speed

selection(3) to the left.

• Keep the venting slots clear to prevent the motor from

overheating.

• Wait for 10minutes before switching the device back on.

Note

Wait for at least 3 minutes after maintenance and

repair work. Only then switch the device back on.

The device still does not operate correctly after these

checks:

Please contact the customer service. If necessary, bring the

device to an authorised specialist electrical company or to

Trotec for repair.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Trotec PAGS10-125 Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Trotec PAGS10-125

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info