Bedienungsanleitung Trotec PAGS20-115 (Seite 19 von 23) (Englisch)

753913

Zoom out

Zoom in

Vorherige Seite

1/23

Nächste Seite

EN 18

cordless angle grinder PAGS 20-115

7. To switch the device off, let go of the on/off switch(5).

Caution

The disc keeps running after the device has been

switched off.

Risk of injury.

Shutdown

Warning of electrical voltage

Do not touch the mains plug with wet or damp hands.

• Switch off the device.

• Hold onto the mains plug while pulling the power cable of

the charger out of the mains socket.

• If required, allow the device to cool down.

• Remove the battery from the device (see Start-up chapter).

• Remove the tool from the device (see Start-up chapter).

• Clean the device according to the Maintenance chapter.

• Store the device according to the Storage chapter.

Available accessories

Warning

Only use accessories and additional equipment

specified in the operating manual.

Using insertion tools or accessories other than those

specified in the operating manual may cause a risk of

injury.

Designation Article number

Set of diamond cutting discs Ø110mm/

115mm

6.225.001.121

Spare battery Multiflex4.0Ah 20V 6.200.000.320

Errors and faults

The device has been checked for proper functioning several

times during production. If malfunctions occur nonetheless,

check the device according to the following list.

Troubleshooting tasks which require the housing to be opened

must only be carried out by an authorized specialist electrical

company or by Trotec.

Slight smoke or odour are emitted during first use:

• This is not a fault. These phenomena disappear after a

brief runtime.

The battery does not charge:

• Check whether the battery is correctly connected to the

quick charger.

Slide the battery into the quick charger in a way that the

battery terminals engage in the quick charger. The battery

must lock in place in the quick charger.

• Check the power connection.

• Check the power cable and mains plug for damages.

• Check the fuse (home).

• Check the quick charger for damages. Should the quick

charger be damaged, stop using it. Contact the Trotec

customer service.

• Check the battery terminals for dirt. Remove any dirt.

• The battery might be defective and have to be replaced.

Only use batteries of the same type.

The device does not start:

• The battery power might be too low. Recharge the battery.

• Check whether the battery is correctly connected to the

device.

Slide the battery onto the device in a way that the battery

terminals engage. The battery must lock in place in the

device.

• Check the battery terminals for dirt. Remove any dirt.

Info

Wait for at least 10 minutes before switching the

device back on.

The cutting disc is loose:

• Check whether you are using a cutting disc that is suited

for this device.

• Make sure that the mounting flange is firmly locked in

place in the designated recesses.

• Make sure that the cutting disc sits flush on the mounting

flange without clearance.

• Make sure that the flat side of the clamping nut rests on

the cutting disc.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Trotec PAGS20-115 Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Trotec PAGS20-115

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info