Bedienungsanleitung Trotec PCSS 10-1400 (Seite 4 von 24) (Englisch)

753910

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

4 EN

portable circular saw PCSS 10-1400

General Power Tool Safety Warnings– Power tool

use and care

•Do not force the power tool. Use the correct power tool

for your application. The correct power tool will do the

job better and safer at the rate for which it was designed.

•Do not use the power tool if the switch does not turn it

on and off. Any power tool that cannot be controlled with

the switch is dangerous and must be repaired.

•Disconnect the plug from the power source and/or

remove the battery pack, if detachable, from the power

tool before making any adjustments, changing

accessories, or storing power tools. Such preventive

safety measures reduce the risk of starting the power tool

accidentally.

•Store idle power tools out of the reach of children and

do not allow persons unfamiliar with the power tool or

these instructions to operate the power tool. Power

tools are dangerous in the hands of untrained users.

•Maintain power tools and accessories. Check for

misalignment or binding of moving parts, breakage of

parts and any other condition that may affect the

power tool's operation. If damaged, have the power

tool repaired before use. Many accidents are caused by

poorly maintained power tools.

•Keep cutting tools sharp and clean. Properly maintained

cutting tools with sharp cutting edges are less likely to

bind and are easier to control.

•Use the power tool, accessories and tool bits etc. in

accordance with these instructions, taking into

account the working conditions and the work to be

performed. Use of the power tool for operations different

from those intended could result in a hazardous situation.

•Keep handles and grasping surfaces dry, clean and

free from oil and grease. Slippery handles and grasping

surfaces do not allow for safe handling and control of the

tool in unexpected situations.

General Power Tool Safety Warnings– Service

•Have your power tool serviced by a qualified repair

person using only identical replacement parts. This will

ensure that the safety of the power tool is maintained.

Device-specific safety warnings for portable

circular saws

Safety warnings for all saws

Sawing methods

•DANGER: Keep hands away from cutting area and the

blade. Keep your second hand on auxiliary handle, or

motor housing. If both hands are holding the saw, they

cannot be cut by the blade.

•Do not reach underneath the workpiece. The guard

cannot protect you from the blade below the workpiece.

•Adjust the cutting depth to the thickness of the

workpiece. Less than a full tooth of the blade teeth should

be visible below the workpiece.

•Never hold piece being cut in your hands or across

your leg. Secure the workpiece to a stable platform. It

is important to support the work properly to minimise body

exposure, blade binding, or loss of control.

•Hold the power tool by its insulated gripping surfaces

when performing an operation where the cutting

accessory may contact hidden wiring or its own cord.

Contact with a "live" wire will also make exposed metal

parts of the power tool "live" and could give the operator

an electric shock.

•When ripping, always use a rip fence or straight edge

guide. This improves the accuracy of cut and reduces the

chance of blade binding.

•Always use saw blades with correct size and shape

(diamond versus round) of arbour holes. Blades that do

not match the mounting hardware of the saw will run

eccentrically, causing loss of control.

•Never use damaged or incorrect blade washers or

bolts. The blade washers and bolt were specially designed

for your saw, for optimum performance and safety of

operation.

Further safety warnings for all saws

Kickback causes and related warnings

A kickback is a sudden reaction to a pinched, bound or

misaligned saw blade, causing an uncontrolled saw to lift up

and out of the workpiece toward the operator.

When the blade is pinched or bound tightly by the kerf closing

down, the blade stalls and the motor reaction drives the unit

rapidly back toward the operator.

If the blade becomes twisted or misaligned in the cut, the teeth

at the back edge of the blade can dig into the top surface of the

workpiece causing the blade to climb out of the kerf and jump

back toward the operator.

Kickback is the result of saw misuse and/or incorrect

operating procedures or conditions and can be avoided by

taking proper precautions as given below.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Trotec PCSS 10-1400 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Trotec PCSS 10-1400

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info