Bedienungsanleitung Trotec PCSS 10-1400 (Seite 5 von 24) (Englisch)

753910

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

EN 5

portable circular saw PCSS 10-1400

•Maintain a firm grip with both hands on the saw and

position your arms to resist kickback forces. Position

your body to either side of the blade, but not in line

with the blade. Kickback could cause the saw to jump

backwards, but kickback forces can be controlled by the

operator, if proper precautions are taken.

•When blade is binding, or when interrupting a cut for

any reason, release the trigger and hold the saw

motionless in the material until the blade comes to a

complete stop. Never attempt to remove the saw from

the work or pull the saw backwards while the blade is

in motion or kickback may occur. Investigate and take

corrective actions to eliminate the cause of blade binding.

•When restarting a saw in the workpiece, centre the

saw blade in the kerf and check that saw teeth are not

engaged into the material. If saw blade is binding, it may

walk up or kickback from the workpiece as the saw is

restarted.

•Support large panels to minimise the risk of blade

pinching and kickback. Large panels tend to sag under

their own weight. Supports must be placed under the

panel on both sides, near the line of cut and near the edge

of the panel.

•Do not use dull or damaged blades. Unsharpened or

improperly set blades produce narrow kerf causing

excessive friction, blade binding and kickback.

•Blade depth and bevel adjusting locking levers must

be tight and secure before making cut. If blade

adjustment shifts while cutting, it may cause binding and

kickback.

•Use extra caution when sawing into existing walls or

other blind areas. The protruding blade may cut objects

that can cause kickback.

Safety warnings for circular saws with pendulum guard

and circular saws with tow guard – Lower guard function

•Check the lower guard for proper closure before each

use. Do not operate the saw if the lower guard does

not move freely and close immediately. Never clamp or

tie the lower guard in the open position. The lower

guard may be bent if the saw accidentally falls to the floor.

Use the retracting lever to raise the guard and make sure

that it moves freely and does not touch the blade or any

other part of the saw at all cutting angles and depths of

cut.

•Check that the lower guard spring operates correctly.

If the guard and spring do not operate correctly, have

the saw serviced before use. Lower guard may operate

sluggishly due to damaged parts, gummy deposits, or a

build-up of debris.

•Lower guard may be retracted manually only for

special cuts such as "plunge cuts" and "compound

cuts". Raise lower guard by retracting lever and as

soon as blade enters the material, the lower guard

must be released. For all other sawing, the lower guard

should operate automatically.

•Always observe that the lower guard is covering the

blade before placing saw down on bench or floor. An

unprotected, coasting blade will cause the saw to walk

backwards, cutting whatever is in its path. Be aware of the

time it takes for the blade to stop after switch is released.

Additional safety warnings for portable circular saws

Warning of laser radiation

Laser class2, Pmax.: <1mW, λ: 400-700nm,

EN60825-1:2014

Do not look directly into the laser beam or the opening

from which it emerges.

Never point the laser beam at people, animals or

reflective surfaces. Even brief eye contact can lead to

eye damage.

Examining the laser output aperture by use of optical

instruments (e.g. magnifying glass, magnifiers and the

like) entails the risk of eye damage.

When working with a laser of class2, observe the

national regulations on wearing eye protection.

•Do not reach into the chip ejector with your hands.

They could be injured by rotating parts.

•Do not work overhead with the saw. In this manner you

do not have sufficient control over the power tool.

•Do not use abrasive wheels.

•Only use saw blades of a diameter specified in the

technical data Using a blade of the wrong size may leave

the blade without proper protection or affect the

functioning of the guard.

•Use suitable detectors to determine if utility lines are

hidden in the work area or call the local utility

company for assistance. Contact with electrical lines

may result in fire and electric shock. Damaging a gas line

may lead to an explosion. Penetrating a water line causes

property damage and may cause an electric shock.

•Do not operate the power tool stationary. It is not

designed for operation with a saw table.

•Do not use high speed steel (HSS) saw blades. Such

saw blades can easily break.

•Do not saw ferrous metals. Red hot chips can ignite the

dust extraction.

•If the supply cord is damaged, it must be replaced with

a special connection line that can be obtained from the

manufacturer or his customer service.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Trotec PCSS 10-1400 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Trotec PCSS 10-1400

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info