753364
13
Zoom out
Zoom in
Vorherige Seite
1/21
Nächste Seite
EN 13
170W multi-function tool PMTS 01-230V
Using a flexible shaft
Note
Never actuate the spindle lock(3) button while the tool
is running! This may damage the tool.
Info
Use the flexible shaft for tasks requiring fine and
precise guidance of the tool.
üThere is no tool in the tool holder(27).
üThe 3.2mm collet chuck(14) is mounted.
1. Unscrew the union nut(28) on the tool by turning the nut in
counter-clockwise direction.
28
2. Slightly pull the inner axis(30) from the union nut(31) of
the flexible shaft.
3. Clamp the inner axis(30) into the tool holder(27) by
proceeding as described in the chapter "Tool change.
4. Slide the union nut(31) of the flexible shaft over the tool
holder(27) and tighten it in clockwise direction.
31
30
Proceed as follows to clamp a tool on the handle(34) of the
flexible shaft:
1. In order to block the spindle at the handle(34), insert the
locking wrench(16) into the spindle lock(33).
2. Slowly turn the tool holder(27) to the locking point until
the locking wrench(16) fully engages with the lock and
fixes it.
3. Loosen the clamping nut(35) by means of the wrench(22)
by turning it in counter-clockwise direction.
33
35 16
34
4. Remove the tool from the tool holder(27), if any.
5. Insert the tool required into the tool holder(27).
6. Tighten the clamping nut(35) in clockwise direction using
the wrench(22).
7. Remove the locking wrench(16) from the spindle lock(33).
8. Check the tool for tight fit.
Warning of hot surface
Ensure that the flexible shaft does not form a loop or
become kinked during operation. There is a risk of the
shaft becoming hot and melting with the hose.
Do not touch the handle if it became hot. Risk of burns.
Using the positioning fixture
Info
The positioning fixture(25) allows for exact, vertical
milling of a groove maintaining a defined depth setting
at the same time. Furthermore, the positioning fixture
enables working with a lateral limit stop.
1. Unscrew the union nut(28) on the tool by turning the nut in
counter-clockwise direction.
13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Trotec PMTS01-230V wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Trotec PMTS01-230V

Trotec PMTS01-230V Bedienungsanleitung - Deutsch - 22 seiten

Trotec PMTS01-230V Bedienungsanleitung - Holländisch - 22 seiten

Trotec PMTS01-230V Bedienungsanleitung - Französisch - 23 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info